So far the CSI port sink and source pads have not had their fmt set at all,
leaving things at the default of SBGGR8_1X8/0x0.
This means that pipeline validation such as e.g. done when calling
media_pipeline_start() will fail since the links to / from the CSI
ports have different fmts on each end.
Store a pointer to the CSI port v4l2-subdev in struct atomisp_input_subdev,
and use this in atomisp_set_sensor_crop_and_fmt() to propagate the sensors
new fmt after a successful set_fmt to the CSI port it is connected too.
The input->csi_port pointer also allows simplifying atomisp_link_setup().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/staging/media/atomisp/pci/atomisp_cmd.c | 7 +++++++
.../media/atomisp/pci/atomisp_internal.h | 1 +
.../staging/media/atomisp/pci/atomisp_subdev.c | 17 +++--------------
.../staging/media/atomisp/pci/atomisp_v4l2.c | 1 +
4 files changed, 12 insertions(+), 14 deletions(-)
@@ -3858,6 +3858,13 @@ static int atomisp_set_sensor_crop_and_fmt(struct atomisp_device *isp,
if (sd_state)
v4l2_subdev_unlock_state(sd_state);
+ /* Propagate new fmt to CSI port */
+ if (which == V4L2_SUBDEV_FORMAT_ACTIVE) {
+ ret = v4l2_subdev_call(input->csi_port, pad, set_fmt, NULL, &format);
+ if (ret)
+ return ret;
+ }
+
*ffmt = format.format;
return ret;
}
@@ -129,6 +129,7 @@ struct atomisp_input_subdev {
bool crop_support;
bool camera_on;
struct v4l2_subdev *camera;
+ struct v4l2_subdev *csi_port;
/* Sensor rects for sensors which support crop */
struct v4l2_rect native_rect;
struct v4l2_rect active_rect;
@@ -644,7 +644,7 @@ static int atomisp_link_setup(struct media_entity *entity,
entity);
struct atomisp_sub_device *asd = v4l2_get_subdevdata(sd);
struct atomisp_device *isp = asd->isp;
- int i, csi_idx, ret;
+ int i, ret;
/* ISP's source is immutable */
if (local != &asd->pads[ATOMISP_SUBDEV_PAD_SINK]) {
@@ -653,24 +653,13 @@ static int atomisp_link_setup(struct media_entity *entity,
return -EINVAL;
}
- for (csi_idx = 0; csi_idx < ATOMISP_CAMERA_NR_PORTS; csi_idx++) {
- if (&isp->csi2_port[csi_idx].pads[CSI2_PAD_SOURCE] == remote)
- break;
- }
-
- if (csi_idx == ATOMISP_CAMERA_NR_PORTS) {
- v4l2_err(sd, "Error cannot find CSI receiver for remote pad\n");
- return -EINVAL;
- }
-
-
for (i = 0; i < isp->input_cnt; i++) {
- if (isp->inputs[i].camera == isp->sensor_subdevs[csi_idx])
+ if (&isp->inputs[i].csi_port->entity.pads[CSI2_PAD_SOURCE] == remote)
break;
}
if (i == isp->input_cnt) {
- v4l2_err(sd, "Error no sensor for CSI receiver %d\n", csi_idx);
+ v4l2_err(sd, "Error no sensor for selected CSI receiver\n");
return -EINVAL;
}
@@ -1058,6 +1058,7 @@ int atomisp_register_device_nodes(struct atomisp_device *isp)
input->type = RAW_CAMERA;
input->port = i;
input->camera = isp->sensor_subdevs[i];
+ input->csi_port = &isp->csi2_port[i].subdev;
atomisp_init_sensor(input);