diff mbox series

[v2,7/7] media: dt-bindings: ov5693: document YAML binding

Message ID 20220627150453.220292-8-tommaso.merciai@amarulasolutions.com (mailing list archive)
State Changes Requested
Delegated to: Sakari Ailus
Headers
Series media: ov5693: cleanup code and add dts support |

Commit Message

Tommaso Merciai June 27, 2022, 3:04 p.m. UTC 
  This patch adds documentation of device tree in YAML schema for the
OV5693 CMOS image sensor from Omnivision

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
---
Changes since v1:
 - Fix allOf position as suggested by Krzysztof
 - Remove port description as suggested by Krzysztof
 - Fix EOF as suggested by Krzysztof

 .../bindings/media/i2c/ovti,ov5693.yaml       | 108 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 109 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml

Comments

Krzysztof Kozlowski June 29, 2022, 10:42 a.m. UTC | #1 
On 27/06/2022 17:04, Tommaso Merciai wrote:
> This patch adds documentation of device tree in YAML schema for the
> OV5693 CMOS image sensor from Omnivision

You could remove "This patch", but it's a nit-pick
https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95

> 
> Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>


Best regards,
Krzysztof
Tommaso Merciai June 29, 2022, 2:38 p.m. UTC | #2 
Hi Krzysztof,

On Wed, Jun 29, 2022 at 12:42:10PM +0200, Krzysztof Kozlowski wrote:
> On 27/06/2022 17:04, Tommaso Merciai wrote:
> > This patch adds documentation of device tree in YAML schema for the
> > OV5693 CMOS image sensor from Omnivision
> 
> You could remove "This patch", but it's a nit-pick
> https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95

No issue :)

I'll fix this in v3.
Thanks for the review.

Regards,
Tommaso

> 
> > 
> > Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
> 
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> 
> 
> Best regards,
> Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
new file mode 100644
index 000000000000..e8e2776efc08
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
@@ -0,0 +1,108 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2022 Amarulasolutions
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV5693 CMOS Sensor
+
+maintainers:
+  - Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
+
+description: |
+  The Omnivision OV5693 is a high performance, 1/4-inch, 5 megapixel, CMOS
+  image sensor that delivers 2592x1944 at 30fps. It provides full-frame,
+  sub-sampled, and windowed 10-bit MIPI images in various formats via the
+  Serial Camera Control Bus (SCCB) interface.
+
+  Supports images sizes: 5 Mpixel, EIS1080p, 1080p, 720p, VGA, QVGA
+
+  OV5693 is programmable through I2C and two-wire Serial Camera Control Bus (SCCB).
+  The sensor output is available via CSI-2 serial data output (up to 2-lane).
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov5693
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      System input clock (aka XVCLK). From 6 to 27 MHz.
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Digital I/O voltage supply, 1.8V.
+
+  avdd-supply:
+    description:
+      Analog voltage supply, 2.8V.
+
+  dvdd-supply:
+    description:
+      Digital core voltage supply, 1.2V.
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls sensor reset.
+      This corresponds to the hardware pin XSHUTDN which is physically
+      active low.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/pinctrl/rockchip.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov5693: camera@36 {
+            compatible = "ovti,ov5693";
+            reg = <0x36>;
+
+            reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&cif_clkout_m0>;
+
+            clocks = <&cru SCLK_CIF_OUT>;
+            assigned-clocks = <&cru SCLK_CIF_OUT>;
+            assigned-clock-rates = <19200000>;
+
+            avdd-supply = <&vcc_1v8>;
+            dvdd-supply = <&vcc_1v2>;
+            dovdd-supply = <&vcc_2v8>;
+
+            rotation = <90>;
+            orientation = <0>;
+
+            port {
+                ucam_out: endpoint {
+                    remote-endpoint = <&mipi_in_ucam>;
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <450000000>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 1fc9ead83d2a..844307cb20c4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14719,6 +14719,7 @@  M:	Daniel Scally <djrscally@gmail.com>
 L:	linux-media@vger.kernel.org
 S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
+F:	Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
 F:	drivers/media/i2c/ov5693.c
 
 OMNIVISION OV5695 SENSOR DRIVER