[v2,07/19] media: ti-vpe: cal: print errors on timeouts
Commit Message
The driver does not print any errors on ComplexIO reset timeout or when
waiting for stop-state, making it difficult to debug and notice
problems.
Add error prints for these cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/media/platform/ti-vpe/cal.c | 8 ++++++++
1 file changed, 8 insertions(+)
Comments
Tomi,
Thanks for the patch.
On 3/19/20 2:50 AM, Tomi Valkeinen wrote:
> The driver does not print any errors on ComplexIO reset timeout or when
> waiting for stop-state, making it difficult to debug and notice
> problems.
>
> Add error prints for these cases.
>
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
> Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
> ---
> drivers/media/platform/ti-vpe/cal.c | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/drivers/media/platform/ti-vpe/cal.c b/drivers/media/platform/ti-vpe/cal.c
> index 838215a3f230..b070c56f8d80 100644
> --- a/drivers/media/platform/ti-vpe/cal.c
> +++ b/drivers/media/platform/ti-vpe/cal.c
> @@ -844,6 +844,11 @@ static void csi2_wait_for_phy(struct cal_ctx *ctx)
> reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)), i,
> (i >= 250) ? "(timeout)" : "");
>
> + if (reg_read_field(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
> + CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK) !=
> + CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED)
> + ctx_err(ctx, "Timeout waiting for Complex IO reset done\n");
> +
Since you are promoting these from debug to error event then removing the related
ctx_dbg statement would make sense then.
I was using these as debug statement before but they are now useless if an error
trace is generated instead.
> /* 4. G. Wait for all enabled lane to reach stop state */
> for (i = 0; i < 10; i++) {
> if (reg_read_field(ctx->dev,
> @@ -857,6 +862,9 @@ static void csi2_wait_for_phy(struct cal_ctx *ctx)
> ctx->csi2_port,
> reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port)),
> (i >= 10) ? "(timeout)" : "");
Same here.
But with that,
Reviewed-by: Benoit Parrot <bparrot@ti.com>
> + if (reg_read_field(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port),
> + CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK) != 0)
> + ctx_err(ctx, "Timeout waiting for stop state\n");
>
> ctx_dbg(1, ctx, "CSI2_%d_REG1 = 0x%08x (Bit(31,28) should be set!)\n",
> (ctx->csi2_port - 1), reg_read(ctx->cc, CAL_CSI2_PHY_REG1));
>
@@ -844,6 +844,11 @@ static void csi2_wait_for_phy(struct cal_ctx *ctx)
reg_read(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port)), i,
(i >= 250) ? "(timeout)" : "");
+ if (reg_read_field(ctx->dev, CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
+ CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK) !=
+ CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED)
+ ctx_err(ctx, "Timeout waiting for Complex IO reset done\n");
+
/* 4. G. Wait for all enabled lane to reach stop state */
for (i = 0; i < 10; i++) {
if (reg_read_field(ctx->dev,
@@ -857,6 +862,9 @@ static void csi2_wait_for_phy(struct cal_ctx *ctx)
ctx->csi2_port,
reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port)),
(i >= 10) ? "(timeout)" : "");
+ if (reg_read_field(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port),
+ CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK) != 0)
+ ctx_err(ctx, "Timeout waiting for stop state\n");
ctx_dbg(1, ctx, "CSI2_%d_REG1 = 0x%08x (Bit(31,28) should be set!)\n",
(ctx->csi2_port - 1), reg_read(ctx->cc, CAL_CSI2_PHY_REG1));