[v2,5/5,media] c8sectpfe: Update DT binding doc with some minor fixes
Commit Message
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
.../devicetree/bindings/media/stih407-c8sectpfe.txt | 16 +++++++---------
1 file changed, 7 insertions(+), 9 deletions(-)
Comments
On Thu, 27 Aug 2015, Peter Griffin wrote:
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> ---
> .../devicetree/bindings/media/stih407-c8sectpfe.txt | 16 +++++++---------
> 1 file changed, 7 insertions(+), 9 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> index e70d840..5d6438c 100644
> --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> @@ -55,21 +55,20 @@ Example:
> status = "okay";
> reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
> reg-names = "stfe", "stfe-ram";
> - interrupts = <0 34 0>, <0 35 0>;
> + interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
> interrupt-names = "stfe-error-irq", "stfe-idle-irq";
> -
> - pinctrl-names = "tsin0-serial", "tsin0-parallel", "tsin3-serial",
> - "tsin4-serial", "tsin5-serial";
> -
> + pinctrl-names = "tsin0-serial",
> + "tsin0-parallel",
> + "tsin3-serial",
> + "tsin4-serial",
> + "tsin5-serial";
> pinctrl-0 = <&pinctrl_tsin0_serial>;
> pinctrl-1 = <&pinctrl_tsin0_parallel>;
> pinctrl-2 = <&pinctrl_tsin3_serial>;
> pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
> pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
> -
> clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
> - clock-names = "stfe";
> -
> + clock-names = "c8sectpfe";
Are you sure you even need this property? I'm thinking that *-names
properties are *usually* only required if there are more than one in a
single property.
> /* tsin0 is TSA on NIMA */
> tsin0: port@0 {
> tsin-num = <0>;
> @@ -78,7 +77,6 @@ Example:
> reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
> dvb-card = <STV0367_TDA18212_NIMA_1>;
> };
> -
My personal preference is to have a '\n' between nodes.
> tsin3: port@3 {
> tsin-num = <3>;
> serial-not-parallel;
But these comments are pretty trivial, so agree or not, or fix-up or
not, it's that big of a deal.
Either way,
Acked-by: Lee Jones <lee.jones@linaro.org>
Hi Lee,
On Fri, 28 Aug 2015, Lee Jones wrote:
> On Thu, 27 Aug 2015, Peter Griffin wrote:
>
> > Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> > ---
> > .../devicetree/bindings/media/stih407-c8sectpfe.txt | 16 +++++++---------
> > 1 file changed, 7 insertions(+), 9 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> > index e70d840..5d6438c 100644
> > --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> > +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> > @@ -55,21 +55,20 @@ Example:
> > status = "okay";
> > reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
> > reg-names = "stfe", "stfe-ram";
> > - interrupts = <0 34 0>, <0 35 0>;
> > + interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
> > interrupt-names = "stfe-error-irq", "stfe-idle-irq";
> > -
> > - pinctrl-names = "tsin0-serial", "tsin0-parallel", "tsin3-serial",
> > - "tsin4-serial", "tsin5-serial";
> > -
> > + pinctrl-names = "tsin0-serial",
> > + "tsin0-parallel",
> > + "tsin3-serial",
> > + "tsin4-serial",
> > + "tsin5-serial";
> > pinctrl-0 = <&pinctrl_tsin0_serial>;
> > pinctrl-1 = <&pinctrl_tsin0_parallel>;
> > pinctrl-2 = <&pinctrl_tsin3_serial>;
> > pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
> > pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
> > -
> > clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
> > - clock-names = "stfe";
> > -
> > + clock-names = "c8sectpfe";
>
> Are you sure you even need this property? I'm thinking that *-names
> properties are *usually* only required if there are more than one in a
> single property.
Yes that is true, but for tsout and merged input stream
functionality the driver will require additional clocks. As I
mentioned in a previous email I hope to add support for this in the
near future.
>
> > /* tsin0 is TSA on NIMA */
> > tsin0: port@0 {
> > tsin-num = <0>;
> > @@ -78,7 +77,6 @@ Example:
> > reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
> > dvb-card = <STV0367_TDA18212_NIMA_1>;
> > };
> > -
>
> My personal preference is to have a '\n' between nodes.
Yes mine as well, I removed it due to your earlier comment about "superflous \n".
I will add it back in again in v3.
>
> > tsin3: port@3 {
> > tsin-num = <3>;
> > serial-not-parallel;
>
> But these comments are pretty trivial, so agree or not, or fix-up or
> not, it's that big of a deal.
I agree all trivial, but will fixup in v3.
>
> Either way,
> Acked-by: Lee Jones <lee.jones@linaro.org>
Thanks & regards,
Peter.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
@@ -55,21 +55,20 @@ Example:
status = "okay";
reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
reg-names = "stfe", "stfe-ram";
- interrupts = <0 34 0>, <0 35 0>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
interrupt-names = "stfe-error-irq", "stfe-idle-irq";
-
- pinctrl-names = "tsin0-serial", "tsin0-parallel", "tsin3-serial",
- "tsin4-serial", "tsin5-serial";
-
+ pinctrl-names = "tsin0-serial",
+ "tsin0-parallel",
+ "tsin3-serial",
+ "tsin4-serial",
+ "tsin5-serial";
pinctrl-0 = <&pinctrl_tsin0_serial>;
pinctrl-1 = <&pinctrl_tsin0_parallel>;
pinctrl-2 = <&pinctrl_tsin3_serial>;
pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
-
clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
- clock-names = "stfe";
-
+ clock-names = "c8sectpfe";
/* tsin0 is TSA on NIMA */
tsin0: port@0 {
tsin-num = <0>;
@@ -78,7 +77,6 @@ Example:
reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
dvb-card = <STV0367_TDA18212_NIMA_1>;
};
-
tsin3: port@3 {
tsin-num = <3>;
serial-not-parallel;