[v6,3/7] media: i2c: max2175: Add MAX2175 support

Message ID 20170531084457.4800-4-ramesh.shanmugasundaram@bp.renesas.com (mailing list archive)
State Accepted, archived
Delegated to: Hans Verkuil
Headers

Commit Message

Ramesh Shanmugasundaram May 31, 2017, 8:44 a.m. UTC
  This patch adds driver support for the MAX2175 chip. This is Maxim
Integrated's RF to Bits tuner front end chip designed for software-defined
radio solutions. This driver exposes the tuner as a sub-device instance
with standard and custom controls to configure the device.

Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
---
v6:
 - Addressed Sakari's comments. They are:
	- Added uapi header file.
	- Added newline at the end of the function before return.
	- Cleaned up header file inclusion.
	- Used fwnode_ apis whereever applicable.
	- Cleaned up debug statements.
	- Removed separate dir for max2175.
 
v5:
 - sck -> Sample clock is clarified in driver documentation (Hans)
 - "refout-load-pF" is renamed to "refout-load" as per updated bindings.
---
 Documentation/media/v4l-drivers/index.rst   |    1 +
 Documentation/media/v4l-drivers/max2175.rst |   60 ++
 drivers/media/i2c/Kconfig                   |   12 +
 drivers/media/i2c/Makefile                  |    2 +
 drivers/media/i2c/max2175.c                 | 1448 +++++++++++++++++++++++++++
 drivers/media/i2c/max2175.h                 |  107 ++
 include/uapi/linux/max2175.h                |   28 +
 7 files changed, 1658 insertions(+)
 create mode 100644 Documentation/media/v4l-drivers/max2175.rst
 create mode 100644 drivers/media/i2c/max2175.c
 create mode 100644 drivers/media/i2c/max2175.h
 create mode 100644 include/uapi/linux/max2175.h
  

Comments

Mauro Carvalho Chehab June 7, 2017, 1:17 p.m. UTC | #1
Em Wed, 31 May 2017 09:44:53 +0100
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> escreveu:

> +++ b/Documentation/media/v4l-drivers/max2175.rst
> @@ -0,0 +1,60 @@
> +Maxim Integrated MAX2175 RF to bits tuner driver
> +================================================
> +
> +The MAX2175 driver implements the following driver-specific controls:
> +
> +``V4L2_CID_MAX2175_I2S_ENABLE``
> +-------------------------------
> +    Enable/Disable I2S output of the tuner.
> +
> +.. flat-table::
> +    :header-rows:  0
> +    :stub-columns: 0
> +    :widths:       1 4
> +
> +    * - ``(0)``
> +      - I2S output is disabled.
> +    * - ``(1)``
> +      - I2S output is enabled.

Hmm... There are other drivers at the subsystem that use I2S
(for audio - not for SDR - but I guess the issue is similar).

On such drivers, the bridge driver controls it directly, being sure
that I2S is enabled when it is expecting some data coming from the
I2S bus.

On some drivers, there are both I2S and A/D inputs at the
bridge chipset. On such drivers, enabling/disabling I2S is
done via VIDIOC_S_INPUT (and optionally via ALSA mixer), being
transparent to the user if the stream comes from a tuner via I2S
or from a directly connected A/D input.

I don't think it is a good idea to enable it via a control, as,
if the bridge driver is expecting data via I2S, disabling it will
cause timeouts at the videobuf handling.

Thanks,
Mauro
  
Ramesh Shanmugasundaram June 8, 2017, 9:42 a.m. UTC | #2
> Subject: Re: [PATCH v6 3/7] media: i2c: max2175: Add MAX2175 support
> 
> Em Wed, 31 May 2017 09:44:53 +0100
> Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> escreveu:
> 
> > +++ b/Documentation/media/v4l-drivers/max2175.rst
> > @@ -0,0 +1,60 @@
> > +Maxim Integrated MAX2175 RF to bits tuner driver
> > +================================================
> > +
> > +The MAX2175 driver implements the following driver-specific controls:
> > +
> > +``V4L2_CID_MAX2175_I2S_ENABLE``
> > +-------------------------------
> > +    Enable/Disable I2S output of the tuner.
> > +
> > +.. flat-table::
> > +    :header-rows:  0
> > +    :stub-columns: 0
> > +    :widths:       1 4
> > +
> > +    * - ``(0)``
> > +      - I2S output is disabled.
> > +    * - ``(1)``
> > +      - I2S output is enabled.
> 
> Hmm... There are other drivers at the subsystem that use I2S (for audio -
> not for SDR - but I guess the issue is similar).
> 
> On such drivers, the bridge driver controls it directly, being sure that
> I2S is enabled when it is expecting some data coming from the I2S bus.
> 
> On some drivers, there are both I2S and A/D inputs at the bridge chipset.
> On such drivers, enabling/disabling I2S is done via VIDIOC_S_INPUT (and
> optionally via ALSA mixer), being transparent to the user if the stream
> comes from a tuner via I2S or from a directly connected A/D input.
> 
> I don't think it is a good idea to enable it via a control, as, if the
> bridge driver is expecting data via I2S, disabling it will cause timeouts
> at the videobuf handling.

The MAX2175 device is exposed as a v4l2 subdev with tuner ops and can interface with an SDR device. When the tuner is configured, the I2S output is enabled by default. From an independent tuner device perspective, this default behaviour is enough and this control may not be needed/used.

However, for the use case here, the R-Car DRIF device acts as the main SDR device and the Maxim MAX2175 provides a sub-dev interface with tuner ops.

+---------------------+                +---------------------+
|                     |-----SCK------->|CLK                  |   
|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
|      (MAX2175)      |-----SD0------->|D0                   |   
|                     |-----SD1------->|D1                   |   
+---------------------+                +---------------------+

The DRIF device design is such that it involves separate register writes to enable Rx on each of the data line. To keep both the data lines in sync it expects the master device to enable output after both the data line Rx are enabled.

This level of control is exposed as a feature in the MAX2175 using this control. When interfaced with DRIF this control is used to achieve the desired functionality. When not interfaced with DRIF, the MAX2175 default behaviour does not have to change because of DRIF and hence this I2S control may be unused. Like MAX2175, DRIF is also an independent device and can interface with a different third party tuner. 

Hence, this I2S enable/disable is exposed as a user control. The end user application (knowing both these devices) is expected to use these controls appropriately. Please let me know if I need to explain anything in further detail.

Thanks,
Ramesh
  
Mauro Carvalho Chehab June 8, 2017, 10:23 a.m. UTC | #3
Em Thu, 8 Jun 2017 09:42:43 +0000
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> escreveu:

> > Subject: Re: [PATCH v6 3/7] media: i2c: max2175: Add MAX2175 support
> > 
> > Em Wed, 31 May 2017 09:44:53 +0100
> > Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> escreveu:
> >   
> > > +++ b/Documentation/media/v4l-drivers/max2175.rst
> > > @@ -0,0 +1,60 @@
> > > +Maxim Integrated MAX2175 RF to bits tuner driver
> > > +================================================
> > > +
> > > +The MAX2175 driver implements the following driver-specific controls:
> > > +
> > > +``V4L2_CID_MAX2175_I2S_ENABLE``
> > > +-------------------------------
> > > +    Enable/Disable I2S output of the tuner.
> > > +
> > > +.. flat-table::
> > > +    :header-rows:  0
> > > +    :stub-columns: 0
> > > +    :widths:       1 4
> > > +
> > > +    * - ``(0)``
> > > +      - I2S output is disabled.
> > > +    * - ``(1)``
> > > +      - I2S output is enabled.  
> > 
> > Hmm... There are other drivers at the subsystem that use I2S (for audio -
> > not for SDR - but I guess the issue is similar).
> > 
> > On such drivers, the bridge driver controls it directly, being sure that
> > I2S is enabled when it is expecting some data coming from the I2S bus.
> > 
> > On some drivers, there are both I2S and A/D inputs at the bridge chipset.
> > On such drivers, enabling/disabling I2S is done via VIDIOC_S_INPUT (and
> > optionally via ALSA mixer), being transparent to the user if the stream
> > comes from a tuner via I2S or from a directly connected A/D input.
> > 
> > I don't think it is a good idea to enable it via a control, as, if the
> > bridge driver is expecting data via I2S, disabling it will cause timeouts
> > at the videobuf handling.  
> 
> The MAX2175 device is exposed as a v4l2 subdev with tuner ops and can interface with an SDR device. When the tuner is configured, the I2S output is enabled by default. From an independent tuner device perspective, this default behaviour is enough and this control may not be needed/used.
> 
> However, for the use case here, the R-Car DRIF device acts as the main SDR device and the Maxim MAX2175 provides a sub-dev interface with tuner ops.
> 
> +---------------------+                +---------------------+
> |                     |-----SCK------->|CLK                  |   
> |       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
> |      (MAX2175)      |-----SD0------->|D0                   |   
> |                     |-----SD1------->|D1                   |   
> +---------------------+                +---------------------+
> 
> The DRIF device design is such that it involves separate register writes to enable Rx on each of the data line. To keep both the data lines in sync it expects the master device to enable output after both the data line Rx are enabled.
> 
> This level of control is exposed as a feature in the MAX2175 using this control. When interfaced with DRIF this control is used to achieve the desired functionality. When not interfaced with DRIF, the MAX2175 default behaviour does not have to change because of DRIF and hence this I2S control may be unused. Like MAX2175, DRIF is also an independent device and can interface with a different third party tuner. 
> 
> Hence, this I2S enable/disable is exposed as a user control. The end user application (knowing both these devices) is expected to use these controls appropriately. Please let me know if I need to explain anything in further detail.


The usecase is clear. That's exactly what other drivers with I2S do,
except that, on those other drivers, they pass I2S control info via
platform_data (they're not platform drivers).

With those drivers, generic applications work as-is via the standard
video, radio or sdr devnodes, without knowing about I2S.

The main difference here is that you're requiring an specialized
application for this device to work, as a generic one won't be
aware of this device-specific control, and may end by exposing this
"internal" control to the end user. That is OK for embedded usage,
but, as soon as this is used on some non-embedded usecase (with
is likely, as there are several PC consumer products using other
chips from Maxim), we'll have problems.

I guess the solution here is to make such control visible only via the
subdev interface.

Thanks,
Mauro
  
Ramesh Shanmugasundaram June 8, 2017, 11:04 a.m. UTC | #4
> Em Thu, 8 Jun 2017 09:42:43 +0000
> Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> escreveu:
> 
> > > Subject: Re: [PATCH v6 3/7] media: i2c: max2175: Add MAX2175 support
> > >
> > > Em Wed, 31 May 2017 09:44:53 +0100
> > > Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
> escreveu:
> > >
> > > > +++ b/Documentation/media/v4l-drivers/max2175.rst
> > > > @@ -0,0 +1,60 @@
> > > > +Maxim Integrated MAX2175 RF to bits tuner driver
> > > > +================================================
> > > > +
> > > > +The MAX2175 driver implements the following driver-specific
> controls:
> > > > +
> > > > +``V4L2_CID_MAX2175_I2S_ENABLE``
> > > > +-------------------------------
> > > > +    Enable/Disable I2S output of the tuner.
> > > > +
> > > > +.. flat-table::
> > > > +    :header-rows:  0
> > > > +    :stub-columns: 0
> > > > +    :widths:       1 4
> > > > +
> > > > +    * - ``(0)``
> > > > +      - I2S output is disabled.
> > > > +    * - ``(1)``
> > > > +      - I2S output is enabled.
> > >
> > > Hmm... There are other drivers at the subsystem that use I2S (for
> > > audio - not for SDR - but I guess the issue is similar).
> > >
> > > On such drivers, the bridge driver controls it directly, being sure
> > > that I2S is enabled when it is expecting some data coming from the I2S
> bus.
> > >
> > > On some drivers, there are both I2S and A/D inputs at the bridge
> chipset.
> > > On such drivers, enabling/disabling I2S is done via VIDIOC_S_INPUT
> > > (and optionally via ALSA mixer), being transparent to the user if
> > > the stream comes from a tuner via I2S or from a directly connected A/D
> input.
> > >
> > > I don't think it is a good idea to enable it via a control, as, if
> > > the bridge driver is expecting data via I2S, disabling it will cause
> > > timeouts at the videobuf handling.
> >
> > The MAX2175 device is exposed as a v4l2 subdev with tuner ops and can
> interface with an SDR device. When the tuner is configured, the I2S output
> is enabled by default. From an independent tuner device perspective, this
> default behaviour is enough and this control may not be needed/used.
> >
> > However, for the use case here, the R-Car DRIF device acts as the main
> SDR device and the Maxim MAX2175 provides a sub-dev interface with tuner
> ops.
> >
> > +---------------------+                +---------------------+
> > |                     |-----SCK------->|CLK                  |
> > |       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
> > |      (MAX2175)      |-----SD0------->|D0                   |
> > |                     |-----SD1------->|D1                   |
> > +---------------------+                +---------------------+
> >
> > The DRIF device design is such that it involves separate register writes
> to enable Rx on each of the data line. To keep both the data lines in sync
> it expects the master device to enable output after both the data line Rx
> are enabled.
> >
> > This level of control is exposed as a feature in the MAX2175 using this
> control. When interfaced with DRIF this control is used to achieve the
> desired functionality. When not interfaced with DRIF, the MAX2175 default
> behaviour does not have to change because of DRIF and hence this I2S
> control may be unused. Like MAX2175, DRIF is also an independent device
> and can interface with a different third party tuner.
> >
> > Hence, this I2S enable/disable is exposed as a user control. The end
> user application (knowing both these devices) is expected to use these
> controls appropriately. Please let me know if I need to explain anything
> in further detail.
> 
> 
> The usecase is clear. That's exactly what other drivers with I2S do,
> except that, on those other drivers, they pass I2S control info via
> platform_data (they're not platform drivers).
> 
> With those drivers, generic applications work as-is via the standard
> video, radio or sdr devnodes, without knowing about I2S.
> 
> The main difference here is that you're requiring an specialized
> application for this device to work, 

Specialized application may be needed for this specific combination of devices (DRIF + MAX2175) only. For MAX2175 alone, a generic application itself would be enough. The MAX2175 will have I2S output enabled by default and the SDR device have to just enable/disable its own RX during .start_streaming/.stop_streaming.

as a generic one won't be aware of
> this device-specific control, and may end by exposing this "internal"
> control to the end user. That is OK for embedded usage, but, as soon as
> this is used on some non-embedded usecase (with is likely, as there are
> several PC consumer products using other chips from Maxim), we'll have
> problems.
> 
> I guess the solution here is to make such control visible only via the
> subdev interface.
> 

Did you mean using v4l2_subdev_tuner_ops? It does not have a method as of today to support this. The video, audio subdev ops supports s_stream method. We may need to create one for tuner ops.

Thanks,
Ramesh
  

Patch

diff --git a/Documentation/media/v4l-drivers/index.rst b/Documentation/media/v4l-drivers/index.rst
index 90fe22a6414a..2e24d6806052 100644
--- a/Documentation/media/v4l-drivers/index.rst
+++ b/Documentation/media/v4l-drivers/index.rst
@@ -42,6 +42,7 @@  For more details see the file COPYING in the source distribution of Linux.
 	davinci-vpbe
 	fimc
 	ivtv
+	max2175
 	meye
 	omap3isp
 	omap4_camera
diff --git a/Documentation/media/v4l-drivers/max2175.rst b/Documentation/media/v4l-drivers/max2175.rst
new file mode 100644
index 000000000000..94fb815f043b
--- /dev/null
+++ b/Documentation/media/v4l-drivers/max2175.rst
@@ -0,0 +1,60 @@ 
+Maxim Integrated MAX2175 RF to bits tuner driver
+================================================
+
+The MAX2175 driver implements the following driver-specific controls:
+
+``V4L2_CID_MAX2175_I2S_ENABLE``
+-------------------------------
+    Enable/Disable I2S output of the tuner.
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 4
+
+    * - ``(0)``
+      - I2S output is disabled.
+    * - ``(1)``
+      - I2S output is enabled.
+
+``V4L2_CID_MAX2175_HSLS``
+-------------------------
+    The high-side/low-side (HSLS) control of the tuner for a given band.
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 4
+
+    * - ``(0)``
+      - The LO frequency position is below the desired frequency.
+    * - ``(1)``
+      - The LO frequency position is above the desired frequency.
+
+``V4L2_CID_MAX2175_RX_MODE (menu)``
+-----------------------------------
+    The Rx mode controls a number of preset parameters of the tuner like
+    sample clock (sck), sampling rate etc. These multiple settings are
+    provided under one single label called Rx mode in the datasheet. The
+    list below shows the supported modes with a brief description.
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 4
+
+    * - ``"Europe modes"``
+    * - ``"FM 1.2" (0)``
+      - This configures FM band with a sample rate of 0.512 million
+        samples/sec with a 10.24 MHz sck.
+    * - ``"DAB 1.2" (1)``
+      - This configures VHF band with a sample rate of 2.048 million
+        samples/sec with a 32.768 MHz sck.
+
+    * - ``"North America modes"``
+    * - ``"FM 1.0" (0)``
+      - This configures FM band with a sample rate of 0.7441875 million
+        samples/sec with a 14.88375 MHz sck.
+    * - ``"DAB 1.2" (1)``
+      - This configures FM band with a sample rate of 0.372 million
+        samples/sec with a 7.441875 MHz sck.
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 7c23b7a1fd05..5e94935c0822 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -793,6 +793,18 @@  config VIDEO_SAA6752HS
 	  To compile this driver as a module, choose M here: the
 	  module will be called saa6752hs.
 
+comment "SDR tuner chips"
+
+config SDR_MAX2175
+	tristate "Maxim 2175 RF to Bits tuner"
+	depends on VIDEO_V4L2 && MEDIA_SDR_SUPPORT && I2C
+	---help---
+	  Support for Maxim 2175 tuner. It is an advanced analog/digital
+	  radio receiver with RF-to-Bits front-end designed for SDR solutions.
+
+	  To compile this driver as a module, choose M here; the
+	  module will be called max2175.
+
 comment "Miscellaneous helper chips"
 
 config VIDEO_THS7303
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 62323ec66be8..5a4a761f7383 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -86,3 +86,5 @@  obj-$(CONFIG_VIDEO_IR_I2C)  += ir-kbd-i2c.o
 obj-$(CONFIG_VIDEO_ML86V7667)	+= ml86v7667.o
 obj-$(CONFIG_VIDEO_OV2659)	+= ov2659.o
 obj-$(CONFIG_VIDEO_TC358743)	+= tc358743.o
+
+obj-$(CONFIG_SDR_MAX2175) += max2175.o
diff --git a/drivers/media/i2c/max2175.c b/drivers/media/i2c/max2175.c
new file mode 100644
index 000000000000..1a9f0e5bf8ff
--- /dev/null
+++ b/drivers/media/i2c/max2175.c
@@ -0,0 +1,1448 @@ 
+/*
+ * Maxim Integrated MAX2175 RF to Bits tuner driver
+ *
+ * This driver & most of the hard coded values are based on the reference
+ * application delivered by Maxim for this device.
+ *
+ * Copyright (C) 2016 Maxim Integrated Products
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/max2175.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+
+#include "max2175.h"
+
+#define DRIVER_NAME "max2175"
+
+#define mxm_dbg(ctx, fmt, arg...) dev_dbg(&ctx->client->dev, fmt, ## arg)
+#define mxm_err(ctx, fmt, arg...) dev_err(&ctx->client->dev, fmt, ## arg)
+
+/* Rx mode */
+struct max2175_rxmode {
+	enum max2175_band band;		/* Associated band */
+	u32 freq;			/* Default freq in Hz */
+	u8 i2s_word_size;		/* Bit value */
+};
+
+/* Register map to define preset values */
+struct max2175_reg_map {
+	u8 idx;				/* Register index */
+	u8 val;				/* Register value */
+};
+
+static const struct max2175_rxmode eu_rx_modes[] = {
+	/* EU modes */
+	[MAX2175_EU_FM_1_2] = { MAX2175_BAND_FM, 98256000, 1 },
+	[MAX2175_DAB_1_2]   = { MAX2175_BAND_VHF, 182640000, 0 },
+};
+
+static const struct max2175_rxmode na_rx_modes[] = {
+	/* NA modes */
+	[MAX2175_NA_FM_1_0] = { MAX2175_BAND_FM, 98255520, 1 },
+	[MAX2175_NA_FM_2_0] = { MAX2175_BAND_FM, 98255520, 6 },
+};
+
+/*
+ * Preset values:
+ * Based on Maxim MAX2175 Register Table revision: 130p10
+ */
+static const u8 full_fm_eu_1p0[] = {
+	0x15, 0x04, 0xb8, 0xe3, 0x35, 0x18, 0x7c, 0x00,
+	0x00, 0x7d, 0x40, 0x08, 0x70, 0x7a, 0x88, 0x91,
+	0x61, 0x61, 0x61, 0x61, 0x5a, 0x0f, 0x34, 0x1c,
+	0x14, 0x88, 0x33, 0x02, 0x00, 0x09, 0x00, 0x65,
+	0x9f, 0x2b, 0x80, 0x00, 0x95, 0x05, 0x2c, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
+	0x4a, 0x08, 0xa8, 0x0e, 0x0e, 0x2f, 0x7e, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0xab, 0x5e, 0xa9,
+	0xae, 0xbb, 0x57, 0x18, 0x3b, 0x03, 0x3b, 0x64,
+	0x40, 0x60, 0x00, 0x2a, 0xbf, 0x3f, 0xff, 0x9f,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0a, 0x00,
+	0xff, 0xfc, 0xef, 0x1c, 0x40, 0x00, 0x00, 0x02,
+	0x00, 0x00, 0xe0, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0xac, 0x40, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x00, 0x00,
+	0x00, 0x47, 0x00, 0x00, 0x11, 0x3f, 0x22, 0x00,
+	0xf1, 0x00, 0x41, 0x03, 0xb0, 0x00, 0x00, 0x00,
+	0x1b,
+};
+
+static const u8 full_fm_na_1p0[] = {
+	0x13, 0x08, 0x8d, 0xc0, 0x35, 0x18, 0x7d, 0x3f,
+	0x7d, 0x75, 0x40, 0x08, 0x70, 0x7a, 0x88, 0x91,
+	0x61, 0x61, 0x61, 0x61, 0x5c, 0x0f, 0x34, 0x1c,
+	0x14, 0x88, 0x33, 0x02, 0x00, 0x01, 0x00, 0x65,
+	0x9f, 0x2b, 0x80, 0x00, 0x95, 0x05, 0x2c, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
+	0x4a, 0x08, 0xa8, 0x0e, 0x0e, 0xaf, 0x7e, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0xab, 0x5e, 0xa9,
+	0xae, 0xbb, 0x57, 0x18, 0x3b, 0x03, 0x3b, 0x64,
+	0x40, 0x60, 0x00, 0x2a, 0xbf, 0x3f, 0xff, 0x9f,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0a, 0x00,
+	0xff, 0xfc, 0xef, 0x1c, 0x40, 0x00, 0x00, 0x02,
+	0x00, 0x00, 0xe0, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0xa6, 0x40, 0x00,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x00, 0x00,
+	0x00, 0x35, 0x00, 0x00, 0x11, 0x3f, 0x22, 0x00,
+	0xf1, 0x00, 0x41, 0x03, 0xb0, 0x00, 0x00, 0x00,
+	0x1b,
+};
+
+/* DAB1.2 settings */
+static const struct max2175_reg_map dab12_map[] = {
+	{ 0x01, 0x13 }, { 0x02, 0x0d }, { 0x03, 0x15 }, { 0x04, 0x55 },
+	{ 0x05, 0x0a }, { 0x06, 0xa0 }, { 0x07, 0x40 }, { 0x08, 0x00 },
+	{ 0x09, 0x00 }, { 0x0a, 0x7d }, { 0x0b, 0x4a }, { 0x0c, 0x28 },
+	{ 0x0e, 0x43 }, { 0x0f, 0xb5 }, { 0x10, 0x31 }, { 0x11, 0x9e },
+	{ 0x12, 0x68 }, { 0x13, 0x9e }, { 0x14, 0x68 }, { 0x15, 0x58 },
+	{ 0x16, 0x2f }, { 0x17, 0x3f }, { 0x18, 0x40 }, { 0x1a, 0x88 },
+	{ 0x1b, 0xaa }, { 0x1c, 0x9a }, { 0x1d, 0x00 }, { 0x1e, 0x00 },
+	{ 0x23, 0x80 }, { 0x24, 0x00 }, { 0x25, 0x00 }, { 0x26, 0x00 },
+	{ 0x27, 0x00 }, { 0x32, 0x08 }, { 0x33, 0xf8 }, { 0x36, 0x2d },
+	{ 0x37, 0x7e }, { 0x55, 0xaf }, { 0x56, 0x3f }, { 0x57, 0xf8 },
+	{ 0x58, 0x99 }, { 0x76, 0x00 }, { 0x77, 0x00 }, { 0x78, 0x02 },
+	{ 0x79, 0x40 }, { 0x82, 0x00 }, { 0x83, 0x00 }, { 0x85, 0x00 },
+	{ 0x86, 0x20 },
+};
+
+/* EU FM 1.2 settings */
+static const struct max2175_reg_map fmeu1p2_map[] = {
+	{ 0x01, 0x15 }, { 0x02, 0x04 }, { 0x03, 0xb8 }, { 0x04, 0xe3 },
+	{ 0x05, 0x35 }, { 0x06, 0x18 }, { 0x07, 0x7c }, { 0x08, 0x00 },
+	{ 0x09, 0x00 }, { 0x0a, 0x73 }, { 0x0b, 0x40 }, { 0x0c, 0x08 },
+	{ 0x0e, 0x7a }, { 0x0f, 0x88 }, { 0x10, 0x91 }, { 0x11, 0x61 },
+	{ 0x12, 0x61 }, { 0x13, 0x61 }, { 0x14, 0x61 }, { 0x15, 0x5a },
+	{ 0x16, 0x0f }, { 0x17, 0x34 }, { 0x18, 0x1c }, { 0x1a, 0x88 },
+	{ 0x1b, 0x33 }, { 0x1c, 0x02 }, { 0x1d, 0x00 }, { 0x1e, 0x01 },
+	{ 0x23, 0x80 }, { 0x24, 0x00 }, { 0x25, 0x95 }, { 0x26, 0x05 },
+	{ 0x27, 0x2c }, { 0x32, 0x08 }, { 0x33, 0xa8 }, { 0x36, 0x2f },
+	{ 0x37, 0x7e }, { 0x55, 0xbf }, { 0x56, 0x3f }, { 0x57, 0xff },
+	{ 0x58, 0x9f }, { 0x76, 0xac }, { 0x77, 0x40 }, { 0x78, 0x00 },
+	{ 0x79, 0x00 }, { 0x82, 0x47 }, { 0x83, 0x00 }, { 0x85, 0x11 },
+	{ 0x86, 0x3f },
+};
+
+/* FM NA 1.0 settings */
+static const struct max2175_reg_map fmna1p0_map[] = {
+	{ 0x01, 0x13 }, { 0x02, 0x08 }, { 0x03, 0x8d }, { 0x04, 0xc0 },
+	{ 0x05, 0x35 }, { 0x06, 0x18 }, { 0x07, 0x7d }, { 0x08, 0x3f },
+	{ 0x09, 0x7d }, { 0x0a, 0x75 }, { 0x0b, 0x40 }, { 0x0c, 0x08 },
+	{ 0x0e, 0x7a }, { 0x0f, 0x88 }, { 0x10, 0x91 }, { 0x11, 0x61 },
+	{ 0x12, 0x61 }, { 0x13, 0x61 }, { 0x14, 0x61 }, { 0x15, 0x5c },
+	{ 0x16, 0x0f }, { 0x17, 0x34 }, { 0x18, 0x1c }, { 0x1a, 0x88 },
+	{ 0x1b, 0x33 }, { 0x1c, 0x02 }, { 0x1d, 0x00 }, { 0x1e, 0x01 },
+	{ 0x23, 0x80 }, { 0x24, 0x00 }, { 0x25, 0x95 }, { 0x26, 0x05 },
+	{ 0x27, 0x2c }, { 0x32, 0x08 }, { 0x33, 0xa8 }, { 0x36, 0xaf },
+	{ 0x37, 0x7e }, { 0x55, 0xbf }, { 0x56, 0x3f }, { 0x57, 0xff },
+	{ 0x58, 0x9f }, { 0x76, 0xa6 }, { 0x77, 0x40 }, { 0x78, 0x00 },
+	{ 0x79, 0x00 }, { 0x82, 0x35 }, { 0x83, 0x00 }, { 0x85, 0x11 },
+	{ 0x86, 0x3f },
+};
+
+/* FM NA 2.0 settings */
+static const struct max2175_reg_map fmna2p0_map[] = {
+	{ 0x01, 0x13 }, { 0x02, 0x08 }, { 0x03, 0x8d }, { 0x04, 0xc0 },
+	{ 0x05, 0x35 }, { 0x06, 0x18 }, { 0x07, 0x7c }, { 0x08, 0x54 },
+	{ 0x09, 0xa7 }, { 0x0a, 0x55 }, { 0x0b, 0x42 }, { 0x0c, 0x48 },
+	{ 0x0e, 0x7a }, { 0x0f, 0x88 }, { 0x10, 0x91 }, { 0x11, 0x61 },
+	{ 0x12, 0x61 }, { 0x13, 0x61 }, { 0x14, 0x61 }, { 0x15, 0x5c },
+	{ 0x16, 0x0f }, { 0x17, 0x34 }, { 0x18, 0x1c }, { 0x1a, 0x88 },
+	{ 0x1b, 0x33 }, { 0x1c, 0x02 }, { 0x1d, 0x00 }, { 0x1e, 0x01 },
+	{ 0x23, 0x80 }, { 0x24, 0x00 }, { 0x25, 0x95 }, { 0x26, 0x05 },
+	{ 0x27, 0x2c }, { 0x32, 0x08 }, { 0x33, 0xa8 }, { 0x36, 0xaf },
+	{ 0x37, 0x7e }, { 0x55, 0xbf }, { 0x56, 0x3f }, { 0x57, 0xff },
+	{ 0x58, 0x9f }, { 0x76, 0xac }, { 0x77, 0xc0 }, { 0x78, 0x00 },
+	{ 0x79, 0x00 }, { 0x82, 0x6b }, { 0x83, 0x00 }, { 0x85, 0x11 },
+	{ 0x86, 0x3f },
+};
+
+static const u16 ch_coeff_dab1[] = {
+	0x001c, 0x0007, 0xffcd, 0x0056, 0xffa4, 0x0033, 0x0027, 0xff61,
+	0x010e, 0xfec0, 0x0106, 0xffb8, 0xff1c, 0x023c, 0xfcb2, 0x039b,
+	0xfd4e, 0x0055, 0x036a, 0xf7de, 0x0d21, 0xee72, 0x1499, 0x6a51,
+};
+
+static const u16 ch_coeff_fmeu[] = {
+	0x0000, 0xffff, 0x0001, 0x0002, 0xfffa, 0xffff, 0x0015, 0xffec,
+	0xffde, 0x0054, 0xfff9, 0xff52, 0x00b8, 0x00a2, 0xfe0a, 0x00af,
+	0x02e3, 0xfc14, 0xfe89, 0x089d, 0xfa2e, 0xf30f, 0x25be, 0x4eb6,
+};
+
+static const u16 eq_coeff_fmeu1_ra02_m6db[] = {
+	0x0040, 0xffc6, 0xfffa, 0x002c, 0x000d, 0xff90, 0x0037, 0x006e,
+	0xffc0, 0xff5b, 0x006a, 0x00f0, 0xff57, 0xfe94, 0x0112, 0x0252,
+	0xfe0c, 0xfc6a, 0x0385, 0x0553, 0xfa49, 0xf789, 0x0b91, 0x1a10,
+};
+
+static const u16 ch_coeff_fmna[] = {
+	0x0001, 0x0003, 0xfffe, 0xfff4, 0x0000, 0x001f, 0x000c, 0xffbc,
+	0xffd3, 0x007d, 0x0075, 0xff33, 0xff01, 0x0131, 0x01ef, 0xfe60,
+	0xfc7a, 0x020e, 0x0656, 0xfd94, 0xf395, 0x02ab, 0x2857, 0x3d3f,
+};
+
+static const u16 eq_coeff_fmna1_ra02_m6db[] = {
+	0xfff1, 0xffe1, 0xffef, 0x000e, 0x0030, 0x002f, 0xfff6, 0xffa7,
+	0xff9d, 0x000a, 0x00a2, 0x00b5, 0xffea, 0xfed9, 0xfec5, 0x003d,
+	0x0217, 0x021b, 0xff5a, 0xfc2b, 0xfcbd, 0x02c4, 0x0ac3, 0x0e85,
+};
+
+static const u8 adc_presets[2][23] = {
+	{
+		0x83, 0x00, 0xcf, 0xb4, 0x0f, 0x2c, 0x0c, 0x49,
+		0x00, 0x00, 0x00, 0x8c,	0x02, 0x02, 0x00, 0x04,
+		0xec, 0x82, 0x4b, 0xcc, 0x01, 0x88, 0x0c,
+	},
+	{
+		0x83, 0x00, 0xcf, 0xb4,	0x0f, 0x2c, 0x0c, 0x49,
+		0x00, 0x00, 0x00, 0x8c,	0x02, 0x20, 0x33, 0x8c,
+		0x57, 0xd7, 0x59, 0xb7,	0x65, 0x0e, 0x0c,
+	},
+};
+
+/* Tuner bands */
+static const struct v4l2_frequency_band eu_bands_rf = {
+	.tuner = 0,
+	.type = V4L2_TUNER_RF,
+	.index = 0,
+	.capability = V4L2_TUNER_CAP_1HZ | V4L2_TUNER_CAP_FREQ_BANDS,
+	.rangelow   = 65000000,
+	.rangehigh  = 240000000,
+};
+
+static const struct v4l2_frequency_band na_bands_rf = {
+	.tuner = 0,
+	.type = V4L2_TUNER_RF,
+	.index = 0,
+	.capability = V4L2_TUNER_CAP_1HZ | V4L2_TUNER_CAP_FREQ_BANDS,
+	.rangelow   = 65000000,
+	.rangehigh  = 108000000,
+};
+
+/* Regmap settings */
+static const struct regmap_range max2175_regmap_volatile_range[] = {
+	regmap_reg_range(0x30, 0x35),
+	regmap_reg_range(0x3a, 0x45),
+	regmap_reg_range(0x59, 0x5e),
+	regmap_reg_range(0x73, 0x75),
+};
+
+static const struct regmap_access_table max2175_volatile_regs = {
+	.yes_ranges = max2175_regmap_volatile_range,
+	.n_yes_ranges = ARRAY_SIZE(max2175_regmap_volatile_range),
+};
+
+static const struct reg_default max2175_reg_defaults[] = {
+	{ 0x00, 0x07},
+};
+
+static const struct regmap_config max2175_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = 0xff,
+	.reg_defaults = max2175_reg_defaults,
+	.num_reg_defaults = ARRAY_SIZE(max2175_reg_defaults),
+	.volatile_table = &max2175_volatile_regs,
+	.cache_type = REGCACHE_FLAT,
+};
+
+struct max2175 {
+	struct v4l2_subdev sd;		/* Sub-device */
+	struct i2c_client *client;	/* I2C client */
+
+	/* Controls */
+	struct v4l2_ctrl_handler ctrl_hdl;
+	struct v4l2_ctrl *lna_gain;	/* LNA gain value */
+	struct v4l2_ctrl *if_gain;	/* I/F gain value */
+	struct v4l2_ctrl *pll_lock;	/* PLL lock */
+	struct v4l2_ctrl *i2s_en;	/* I2S output enable */
+	struct v4l2_ctrl *hsls;		/* High-side/Low-side polarity */
+	struct v4l2_ctrl *rx_mode;	/* Receive mode */
+
+	/* Regmap */
+	struct regmap *regmap;
+
+	/* Cached configuration */
+	u32 freq;			/* Tuned freq In Hz */
+	const struct max2175_rxmode *rx_modes;		/* EU or NA modes */
+	const struct v4l2_frequency_band *bands_rf;	/* EU or NA bands */
+
+	/* Device settings */
+	unsigned long xtal_freq;	/* Ref Oscillator freq in Hz */
+	u32 decim_ratio;
+	bool master;			/* Master/Slave */
+	bool am_hiz;			/* AM Hi-Z filter */
+
+	/* ROM values */
+	u8 rom_bbf_bw_am;
+	u8 rom_bbf_bw_fm;
+	u8 rom_bbf_bw_dab;
+
+	/* Driver private variables */
+	bool mode_resolved;		/* Flag to sanity check settings */
+};
+
+static inline struct max2175 *max2175_from_sd(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct max2175, sd);
+}
+
+static inline struct max2175 *max2175_from_ctrl_hdl(struct v4l2_ctrl_handler *h)
+{
+	return container_of(h, struct max2175, ctrl_hdl);
+}
+
+/* Get bitval of a given val */
+static inline u8 max2175_get_bitval(u8 val, u8 msb, u8 lsb)
+{
+	return (val & GENMASK(msb, lsb)) >> lsb;
+}
+
+/* Read/Write bit(s) on top of regmap */
+static int max2175_read(struct max2175 *ctx, u8 idx, u8 *val)
+{
+	u32 regval;
+	int ret;
+
+	ret = regmap_read(ctx->regmap, idx, &regval);
+	if (ret)
+		mxm_err(ctx, "read ret(%d): idx 0x%02x\n", ret, idx);
+	else
+		*val = regval;
+
+	return ret;
+}
+
+static int max2175_write(struct max2175 *ctx, u8 idx, u8 val)
+{
+	int ret;
+
+	ret = regmap_write(ctx->regmap, idx, val);
+	if (ret)
+		mxm_err(ctx, "write ret(%d): idx 0x%02x val 0x%02x\n",
+			ret, idx, val);
+
+	return ret;
+}
+
+static u8 max2175_read_bits(struct max2175 *ctx, u8 idx, u8 msb, u8 lsb)
+{
+	u8 val;
+
+	if (max2175_read(ctx, idx, &val))
+		return 0;
+
+	return max2175_get_bitval(val, msb, lsb);
+}
+
+static int max2175_write_bits(struct max2175 *ctx, u8 idx,
+			     u8 msb, u8 lsb, u8 newval)
+{
+	int ret = regmap_update_bits(ctx->regmap, idx, GENMASK(msb, lsb),
+				     newval << lsb);
+
+	if (ret)
+		mxm_err(ctx, "wbits ret(%d): idx 0x%02x\n", ret, idx);
+
+	return ret;
+}
+
+static int max2175_write_bit(struct max2175 *ctx, u8 idx, u8 bit, u8 newval)
+{
+	return max2175_write_bits(ctx, idx, bit, bit, newval);
+}
+
+/* Checks expected pattern every msec until timeout */
+static int max2175_poll_timeout(struct max2175 *ctx, u8 idx, u8 msb, u8 lsb,
+				u8 exp_bitval, u32 timeout_ms)
+{
+	unsigned int val;
+
+	return regmap_read_poll_timeout(ctx->regmap, idx, val,
+			(max2175_get_bitval(val, msb, lsb) == exp_bitval),
+			1000, timeout_ms * 1000);
+}
+
+static int max2175_poll_csm_ready(struct max2175 *ctx)
+{
+	int ret;
+
+	ret = max2175_poll_timeout(ctx, 69, 1, 1, 0, 50);
+	if (ret)
+		mxm_err(ctx, "csm not ready\n");
+
+	return ret;
+}
+
+#define MAX2175_IS_BAND_AM(ctx)		\
+	(max2175_read_bits(ctx, 5, 1, 0) == MAX2175_BAND_AM)
+
+#define MAX2175_IS_BAND_VHF(ctx)	\
+	(max2175_read_bits(ctx, 5, 1, 0) == MAX2175_BAND_VHF)
+
+#define MAX2175_IS_FM_MODE(ctx)		\
+	(max2175_read_bits(ctx, 12, 5, 4) == 0)
+
+#define MAX2175_IS_FMHD_MODE(ctx)	\
+	(max2175_read_bits(ctx, 12, 5, 4) == 1)
+
+#define MAX2175_IS_DAB_MODE(ctx)	\
+	(max2175_read_bits(ctx, 12, 5, 4) == 2)
+
+static int max2175_band_from_freq(u32 freq)
+{
+	if (freq >= 144000 && freq <= 26100000)
+		return MAX2175_BAND_AM;
+	else if (freq >= 65000000 && freq <= 108000000)
+		return MAX2175_BAND_FM;
+
+	return MAX2175_BAND_VHF;
+}
+
+static void max2175_i2s_enable(struct max2175 *ctx, bool enable)
+{
+	if (enable)
+		/* Stuff bits are zeroed */
+		max2175_write_bits(ctx, 104, 3, 0, 2);
+	else
+		/* Keep SCK alive */
+		max2175_write_bits(ctx, 104, 3, 0, 9);
+	mxm_dbg(ctx, "i2s %sabled\n", enable ? "en" : "dis");
+}
+
+static void max2175_set_filter_coeffs(struct max2175 *ctx, u8 m_sel,
+				      u8 bank, const u16 *coeffs)
+{
+	unsigned int i;
+	u8 coeff_addr, upper_address = 24;
+
+	mxm_dbg(ctx, "set_filter_coeffs: m_sel %d bank %d\n", m_sel, bank);
+	max2175_write_bits(ctx, 114, 5, 4, m_sel);
+
+	if (m_sel == 2)
+		upper_address = 12;
+
+	for (i = 0; i < upper_address; i++) {
+		coeff_addr = i + bank * 24;
+		max2175_write(ctx, 115, coeffs[i] >> 8);
+		max2175_write(ctx, 116, coeffs[i]);
+		max2175_write(ctx, 117, coeff_addr | 1 << 7);
+	}
+	max2175_write_bit(ctx, 117, 7, 0);
+}
+
+static void max2175_load_fmeu_1p2(struct max2175 *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(fmeu1p2_map); i++)
+		max2175_write(ctx, fmeu1p2_map[i].idx, fmeu1p2_map[i].val);
+
+	ctx->decim_ratio = 36;
+
+	/* Load the Channel Filter Coefficients into channel filter bank #2 */
+	max2175_set_filter_coeffs(ctx, MAX2175_CH_MSEL, 0, ch_coeff_fmeu);
+	max2175_set_filter_coeffs(ctx, MAX2175_EQ_MSEL, 0,
+				  eq_coeff_fmeu1_ra02_m6db);
+}
+
+static void max2175_load_dab_1p2(struct max2175 *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(dab12_map); i++)
+		max2175_write(ctx, dab12_map[i].idx, dab12_map[i].val);
+
+	ctx->decim_ratio = 1;
+
+	/* Load the Channel Filter Coefficients into channel filter bank #2 */
+	max2175_set_filter_coeffs(ctx, MAX2175_CH_MSEL, 2, ch_coeff_dab1);
+}
+
+static void max2175_load_fmna_1p0(struct max2175 *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(fmna1p0_map); i++)
+		max2175_write(ctx, fmna1p0_map[i].idx, fmna1p0_map[i].val);
+}
+
+static void max2175_load_fmna_2p0(struct max2175 *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(fmna2p0_map); i++)
+		max2175_write(ctx, fmna2p0_map[i].idx, fmna2p0_map[i].val);
+}
+
+static void max2175_set_bbfilter(struct max2175 *ctx)
+{
+	if (MAX2175_IS_BAND_AM(ctx)) {
+		max2175_write_bits(ctx, 12, 3, 0, ctx->rom_bbf_bw_am);
+		mxm_dbg(ctx, "set_bbfilter AM: rom %d\n", ctx->rom_bbf_bw_am);
+	} else if (MAX2175_IS_DAB_MODE(ctx)) {
+		max2175_write_bits(ctx, 12, 3, 0, ctx->rom_bbf_bw_dab);
+		mxm_dbg(ctx, "set_bbfilter DAB: rom %d\n", ctx->rom_bbf_bw_dab);
+	} else {
+		max2175_write_bits(ctx, 12, 3, 0, ctx->rom_bbf_bw_fm);
+		mxm_dbg(ctx, "set_bbfilter FM: rom %d\n", ctx->rom_bbf_bw_fm);
+	}
+}
+
+static bool max2175_set_csm_mode(struct max2175 *ctx,
+			  enum max2175_csm_mode new_mode)
+{
+	int ret = max2175_poll_csm_ready(ctx);
+
+	if (ret)
+		return ret;
+
+	max2175_write_bits(ctx, 0, 2, 0, new_mode);
+	mxm_dbg(ctx, "set csm new mode %d\n", new_mode);
+
+	/* Wait for a fixed settle down time depending on new mode */
+	switch (new_mode) {
+	case MAX2175_PRESET_TUNE:
+		usleep_range(51100, 51500);	/* 51.1ms */
+		break;
+	/*
+	 * Other mode switches need different sleep values depending on band &
+	 * mode
+	 */
+	default:
+		break;
+	}
+
+	return max2175_poll_csm_ready(ctx);
+}
+
+static int max2175_csm_action(struct max2175 *ctx,
+			      enum max2175_csm_mode action)
+{
+	int ret;
+
+	mxm_dbg(ctx, "csm_action: %d\n", action);
+
+	/* Other actions can be added in future when needed */
+	ret = max2175_set_csm_mode(ctx, MAX2175_LOAD_TO_BUFFER);
+	if (ret)
+		return ret;
+
+	return max2175_set_csm_mode(ctx, MAX2175_PRESET_TUNE);
+}
+
+static int max2175_set_lo_freq(struct max2175 *ctx, u32 lo_freq)
+{
+	u8 lo_mult, loband_bits = 0, vcodiv_bits = 0;
+	u32 int_desired, frac_desired;
+	enum max2175_band band;
+	int ret;
+
+	band = max2175_read_bits(ctx, 5, 1, 0);
+	switch (band) {
+	case MAX2175_BAND_AM:
+		lo_mult = 16;
+		break;
+	case MAX2175_BAND_FM:
+		if (lo_freq <= 74700000) {
+			lo_mult = 16;
+		} else if (lo_freq > 74700000 && lo_freq <= 110000000) {
+			loband_bits = 1;
+			lo_mult = 8;
+		} else {
+			loband_bits = 1;
+			vcodiv_bits = 3;
+			lo_mult = 8;
+		}
+		break;
+	case MAX2175_BAND_VHF:
+		if (lo_freq <= 210000000)
+			vcodiv_bits = 2;
+		else
+			vcodiv_bits = 1;
+
+		loband_bits = 2;
+		lo_mult = 4;
+		break;
+	default:
+		loband_bits = 3;
+		vcodiv_bits = 2;
+		lo_mult = 2;
+		break;
+	}
+
+	if (band == MAX2175_BAND_L)
+		lo_freq /= lo_mult;
+	else
+		lo_freq *= lo_mult;
+
+	int_desired = lo_freq / ctx->xtal_freq;
+	frac_desired = div_u64((u64)(lo_freq % ctx->xtal_freq) << 20,
+			       ctx->xtal_freq);
+
+	/* Check CSM is not busy */
+	ret = max2175_poll_csm_ready(ctx);
+	if (ret)
+		return ret;
+
+	mxm_dbg(ctx, "lo_mult %u int %u  frac %u\n",
+		lo_mult, int_desired, frac_desired);
+
+	/* Write the calculated values to the appropriate registers */
+	max2175_write(ctx, 1, int_desired);
+	max2175_write_bits(ctx, 2, 3, 0, (frac_desired >> 16) & 0xf);
+	max2175_write(ctx, 3, frac_desired >> 8);
+	max2175_write(ctx, 4, frac_desired);
+	max2175_write_bits(ctx, 5, 3, 2, loband_bits);
+	max2175_write_bits(ctx, 6, 7, 6, vcodiv_bits);
+
+	return ret;
+}
+
+/*
+ * Helper similar to DIV_ROUND_CLOSEST but an inline function that accepts s64
+ * dividend and s32 divisor
+ */
+static inline s64 max2175_round_closest(s64 dividend, s32 divisor)
+{
+	if ((dividend > 0 && divisor > 0) || (dividend < 0 && divisor < 0))
+		return div_s64(dividend + divisor / 2, divisor);
+
+	return div_s64(dividend - divisor / 2, divisor);
+}
+
+static int max2175_set_nco_freq(struct max2175 *ctx, s32 nco_freq)
+{
+	s32 clock_rate = ctx->xtal_freq / ctx->decim_ratio;
+	u32 nco_reg, abs_nco_freq = abs(nco_freq);
+	s64 nco_val_desired;
+	int ret;
+
+	if (abs_nco_freq < clock_rate / 2) {
+		nco_val_desired = 2 * nco_freq;
+	} else {
+		nco_val_desired = 2 * (clock_rate - abs_nco_freq);
+		if (nco_freq < 0)
+			nco_val_desired = -nco_val_desired;
+	}
+
+	nco_reg = max2175_round_closest(nco_val_desired << 20, clock_rate);
+
+	if (nco_freq < 0)
+		nco_reg += 0x200000;
+
+	/* Check CSM is not busy */
+	ret = max2175_poll_csm_ready(ctx);
+	if (ret)
+		return ret;
+
+	mxm_dbg(ctx, "freq %d desired %lld reg %u\n",
+		nco_freq, nco_val_desired, nco_reg);
+
+	/* Write the calculated values to the appropriate registers */
+	max2175_write_bits(ctx, 7, 4, 0, (nco_reg >> 16) & 0x1f);
+	max2175_write(ctx, 8, nco_reg >> 8);
+	max2175_write(ctx, 9, nco_reg);
+
+	return ret;
+}
+
+static int max2175_set_rf_freq_non_am_bands(struct max2175 *ctx, u64 freq,
+					    u32 lo_pos)
+{
+	s64 adj_freq, low_if_freq;
+	int ret;
+
+	mxm_dbg(ctx, "rf_freq: non AM bands\n");
+
+	if (MAX2175_IS_FM_MODE(ctx))
+		low_if_freq = 128000;
+	else if (MAX2175_IS_FMHD_MODE(ctx))
+		low_if_freq = 228000;
+	else
+		return max2175_set_lo_freq(ctx, freq);
+
+	if (MAX2175_IS_BAND_VHF(ctx) == (lo_pos == MAX2175_LO_ABOVE_DESIRED))
+		adj_freq = freq + low_if_freq;
+	else
+		adj_freq = freq - low_if_freq;
+
+	ret = max2175_set_lo_freq(ctx, adj_freq);
+	if (ret)
+		return ret;
+
+	return max2175_set_nco_freq(ctx, -low_if_freq);
+}
+
+static int max2175_set_rf_freq(struct max2175 *ctx, u64 freq, u32 lo_pos)
+{
+	int ret;
+
+	if (MAX2175_IS_BAND_AM(ctx))
+		ret = max2175_set_nco_freq(ctx, freq);
+	else
+		ret = max2175_set_rf_freq_non_am_bands(ctx, freq, lo_pos);
+
+	mxm_dbg(ctx, "set_rf_freq: ret %d freq %llu\n", ret, freq);
+
+	return ret;
+}
+
+static int max2175_tune_rf_freq(struct max2175 *ctx, u64 freq, u32 hsls)
+{
+	int ret;
+
+	ret = max2175_set_rf_freq(ctx, freq, hsls);
+	if (ret)
+		return ret;
+
+	ret = max2175_csm_action(ctx, MAX2175_BUFFER_PLUS_PRESET_TUNE);
+	if (ret)
+		return ret;
+
+	mxm_dbg(ctx, "tune_rf_freq: old %u new %llu\n", ctx->freq, freq);
+	ctx->freq = freq;
+
+	return ret;
+}
+
+static void max2175_set_hsls(struct max2175 *ctx, u32 lo_pos)
+{
+	mxm_dbg(ctx, "set_hsls: lo_pos %u\n", lo_pos);
+
+	if ((lo_pos == MAX2175_LO_BELOW_DESIRED) == MAX2175_IS_BAND_VHF(ctx))
+		max2175_write_bit(ctx, 5, 4, 1);
+	else
+		max2175_write_bit(ctx, 5, 4, 0);
+}
+
+static void max2175_set_eu_rx_mode(struct max2175 *ctx, u32 rx_mode)
+{
+	switch (rx_mode) {
+	case MAX2175_EU_FM_1_2:
+		max2175_load_fmeu_1p2(ctx);
+		break;
+
+	case MAX2175_DAB_1_2:
+		max2175_load_dab_1p2(ctx);
+		break;
+	}
+	/* Master is the default setting */
+	if (!ctx->master)
+		max2175_write_bit(ctx, 30, 7, 1);
+}
+
+static void max2175_set_na_rx_mode(struct max2175 *ctx, u32 rx_mode)
+{
+	switch (rx_mode) {
+	case MAX2175_NA_FM_1_0:
+		max2175_load_fmna_1p0(ctx);
+		break;
+	case MAX2175_NA_FM_2_0:
+		max2175_load_fmna_2p0(ctx);
+		break;
+	}
+	/* Master is the default setting */
+	if (!ctx->master)
+		max2175_write_bit(ctx, 30, 7, 1);
+
+	ctx->decim_ratio = 27;
+
+	/* Load the Channel Filter Coefficients into channel filter bank #2 */
+	max2175_set_filter_coeffs(ctx, MAX2175_CH_MSEL, 0, ch_coeff_fmna);
+	max2175_set_filter_coeffs(ctx, MAX2175_EQ_MSEL, 0,
+				  eq_coeff_fmna1_ra02_m6db);
+}
+
+static int max2175_set_rx_mode(struct max2175 *ctx, u32 rx_mode)
+{
+	mxm_dbg(ctx, "set_rx_mode: %u am_hiz %u\n", rx_mode, ctx->am_hiz);
+	if (ctx->xtal_freq == MAX2175_EU_XTAL_FREQ)
+		max2175_set_eu_rx_mode(ctx, rx_mode);
+	else
+		max2175_set_na_rx_mode(ctx, rx_mode);
+
+	if (ctx->am_hiz) {
+		mxm_dbg(ctx, "setting AM HiZ related config\n");
+		max2175_write_bit(ctx, 50, 5, 1);
+		max2175_write_bit(ctx, 90, 7, 1);
+		max2175_write_bits(ctx, 73, 1, 0, 2);
+		max2175_write_bits(ctx, 80, 5, 0, 33);
+	}
+
+	/* Load BB filter trim values saved in ROM */
+	max2175_set_bbfilter(ctx);
+
+	/* Set HSLS */
+	max2175_set_hsls(ctx, ctx->hsls->cur.val);
+
+	/* Use i2s enable settings */
+	max2175_i2s_enable(ctx, ctx->i2s_en->cur.val);
+
+	ctx->mode_resolved = true;
+
+	return 0;
+}
+
+static int max2175_rx_mode_from_freq(struct max2175 *ctx, u32 freq, u32 *mode)
+{
+	unsigned int i;
+	int band = max2175_band_from_freq(freq);
+
+	/* Pick the first match always */
+	for (i = 0; i <= ctx->rx_mode->maximum; i++) {
+		if (ctx->rx_modes[i].band == band) {
+			*mode = i;
+			mxm_dbg(ctx, "rx_mode_from_freq: freq %u mode %d\n",
+				freq, *mode);
+			return 0;
+		}
+	}
+
+	return -EINVAL;
+}
+
+static bool max2175_freq_rx_mode_valid(struct max2175 *ctx,
+					 u32 mode, u32 freq)
+{
+	int band = max2175_band_from_freq(freq);
+
+	return (ctx->rx_modes[mode].band == band);
+}
+
+static void max2175_load_adc_presets(struct max2175 *ctx)
+{
+	unsigned int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(adc_presets); i++)
+		for (j = 0; j < ARRAY_SIZE(adc_presets[0]); j++)
+			max2175_write(ctx, 146 + j + i * 55, adc_presets[i][j]);
+}
+
+static int max2175_init_power_manager(struct max2175 *ctx)
+{
+	int ret;
+
+	/* Execute on-chip power-up/calibration */
+	max2175_write_bit(ctx, 99, 2, 0);
+	usleep_range(1000, 1500);
+	max2175_write_bit(ctx, 99, 2, 1);
+
+	/* Wait for the power manager to finish. */
+	ret = max2175_poll_timeout(ctx, 69, 7, 7, 1, 50);
+	if (ret)
+		mxm_err(ctx, "init pm failed\n");
+
+	return ret;
+}
+
+static int max2175_recalibrate_adc(struct max2175 *ctx)
+{
+	int ret;
+
+	/* ADC Re-calibration */
+	max2175_write(ctx, 150, 0xff);
+	max2175_write(ctx, 205, 0xff);
+	max2175_write(ctx, 147, 0x20);
+	max2175_write(ctx, 147, 0x00);
+	max2175_write(ctx, 202, 0x20);
+	max2175_write(ctx, 202, 0x00);
+
+	ret = max2175_poll_timeout(ctx, 69, 4, 3, 3, 50);
+	if (ret)
+		mxm_err(ctx, "adc recalibration failed\n");
+
+	return ret;
+}
+
+static u8 max2175_read_rom(struct max2175 *ctx, u8 row)
+{
+	u8 data = 0;
+
+	max2175_write_bit(ctx, 56, 4, 0);
+	max2175_write_bits(ctx, 56, 3, 0, row);
+
+	usleep_range(2000, 2500);
+	max2175_read(ctx, 58, &data);
+
+	max2175_write_bits(ctx, 56, 3, 0, 0);
+
+	mxm_dbg(ctx, "read_rom: row %d data 0x%02x\n", row, data);
+
+	return data;
+}
+
+static void max2175_load_from_rom(struct max2175 *ctx)
+{
+	u8 data = 0;
+
+	data = max2175_read_rom(ctx, 0);
+	ctx->rom_bbf_bw_am = data & 0x0f;
+	max2175_write_bits(ctx, 81, 3, 0, data >> 4);
+
+	data = max2175_read_rom(ctx, 1);
+	ctx->rom_bbf_bw_fm = data & 0x0f;
+	ctx->rom_bbf_bw_dab = data >> 4;
+
+	data = max2175_read_rom(ctx, 2);
+	max2175_write_bits(ctx, 82, 4, 0, data & 0x1f);
+	max2175_write_bits(ctx, 82, 7, 5, data >> 5);
+
+	data = max2175_read_rom(ctx, 3);
+	if (ctx->am_hiz) {
+		data &= 0x0f;
+		data |= max2175_read_rom(ctx, 7) & 0x40 >> 2;
+		if (!data)
+			data |= 2;
+	} else {
+		data = data & 0xf0 >> 4;
+		data |= max2175_read_rom(ctx, 7) & 0x80 >> 3;
+		if (!data)
+			data |= 30;
+	}
+	max2175_write_bits(ctx, 80, 5, 0, data + 31);
+
+	data = max2175_read_rom(ctx, 6);
+	max2175_write_bits(ctx, 81, 7, 6, data >> 6);
+}
+
+static void max2175_load_full_fm_eu_1p0(struct max2175 *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(full_fm_eu_1p0); i++)
+		max2175_write(ctx, i + 1, full_fm_eu_1p0[i]);
+
+	usleep_range(5000, 5500);
+	ctx->decim_ratio = 36;
+}
+
+static void max2175_load_full_fm_na_1p0(struct max2175 *ctx)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(full_fm_na_1p0); i++)
+		max2175_write(ctx, i + 1, full_fm_na_1p0[i]);
+
+	usleep_range(5000, 5500);
+	ctx->decim_ratio = 27;
+}
+
+static int max2175_core_init(struct max2175 *ctx, u32 refout_bits)
+{
+	int ret;
+
+	/* MAX2175 uses 36.864MHz clock for EU & 40.154MHz for NA region */
+	if (ctx->xtal_freq == MAX2175_EU_XTAL_FREQ)
+		max2175_load_full_fm_eu_1p0(ctx);
+	else
+		max2175_load_full_fm_na_1p0(ctx);
+
+	/* The default settings assume master */
+	if (!ctx->master)
+		max2175_write_bit(ctx, 30, 7, 1);
+
+	mxm_dbg(ctx, "refout_bits %u\n", refout_bits);
+
+	/* Set REFOUT */
+	max2175_write_bits(ctx, 56, 7, 5, refout_bits);
+
+	/* ADC Reset */
+	max2175_write_bit(ctx, 99, 1, 0);
+	usleep_range(1000, 1500);
+	max2175_write_bit(ctx, 99, 1, 1);
+
+	/* Load ADC preset values */
+	max2175_load_adc_presets(ctx);
+
+	/* Initialize the power management state machine */
+	ret = max2175_init_power_manager(ctx);
+	if (ret)
+		return ret;
+
+	/* Recalibrate ADC */
+	ret = max2175_recalibrate_adc(ctx);
+	if (ret)
+		return ret;
+
+	/* Load ROM values to appropriate registers */
+	max2175_load_from_rom(ctx);
+
+	if (ctx->xtal_freq == MAX2175_EU_XTAL_FREQ) {
+		/* Load FIR coefficients into bank 0 */
+		max2175_set_filter_coeffs(ctx, MAX2175_CH_MSEL, 0,
+					  ch_coeff_fmeu);
+		max2175_set_filter_coeffs(ctx, MAX2175_EQ_MSEL, 0,
+					  eq_coeff_fmeu1_ra02_m6db);
+	} else {
+		/* Load FIR coefficients into bank 0 */
+		max2175_set_filter_coeffs(ctx, MAX2175_CH_MSEL, 0,
+					  ch_coeff_fmna);
+		max2175_set_filter_coeffs(ctx, MAX2175_EQ_MSEL, 0,
+					  eq_coeff_fmna1_ra02_m6db);
+	}
+	mxm_dbg(ctx, "core initialized\n");
+
+	return 0;
+}
+
+static void max2175_s_ctrl_rx_mode(struct max2175 *ctx, u32 rx_mode)
+{
+	/* Load mode. Range check already done */
+	max2175_set_rx_mode(ctx, rx_mode);
+
+	mxm_dbg(ctx, "s_ctrl_rx_mode: %u curr freq %u\n", rx_mode, ctx->freq);
+
+	/* Check if current freq valid for mode & update */
+	if (max2175_freq_rx_mode_valid(ctx, rx_mode, ctx->freq))
+		max2175_tune_rf_freq(ctx, ctx->freq, ctx->hsls->cur.val);
+	else
+		/* Use default freq of mode if current freq is not valid */
+		max2175_tune_rf_freq(ctx, ctx->rx_modes[rx_mode].freq,
+				     ctx->hsls->cur.val);
+}
+
+static int max2175_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct max2175 *ctx = max2175_from_ctrl_hdl(ctrl->handler);
+
+	mxm_dbg(ctx, "s_ctrl: id 0x%x, val %u\n", ctrl->id, ctrl->val);
+	switch (ctrl->id) {
+	case V4L2_CID_MAX2175_I2S_ENABLE:
+		max2175_i2s_enable(ctx, ctrl->val);
+		break;
+	case V4L2_CID_MAX2175_HSLS:
+		max2175_set_hsls(ctx, ctrl->val);
+		break;
+	case V4L2_CID_MAX2175_RX_MODE:
+		max2175_s_ctrl_rx_mode(ctx, ctrl->val);
+		break;
+	}
+
+	return 0;
+}
+
+static u32 max2175_get_lna_gain(struct max2175 *ctx)
+{
+	enum max2175_band band = max2175_read_bits(ctx, 5, 1, 0);
+
+	switch (band) {
+	case MAX2175_BAND_AM:
+		return max2175_read_bits(ctx, 51, 3, 0);
+	case MAX2175_BAND_FM:
+		return max2175_read_bits(ctx, 50, 3, 0);
+	case MAX2175_BAND_VHF:
+		return max2175_read_bits(ctx, 52, 5, 0);
+	default:
+		return 0;
+	}
+}
+
+static int max2175_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct max2175 *ctx = max2175_from_ctrl_hdl(ctrl->handler);
+
+	switch (ctrl->id) {
+	case V4L2_CID_RF_TUNER_LNA_GAIN:
+		ctrl->val = max2175_get_lna_gain(ctx);
+		break;
+	case V4L2_CID_RF_TUNER_IF_GAIN:
+		ctrl->val = max2175_read_bits(ctx, 49, 4, 0);
+		break;
+	case V4L2_CID_RF_TUNER_PLL_LOCK:
+		ctrl->val = (max2175_read_bits(ctx, 60, 7, 6) == 3);
+		break;
+	}
+
+	return 0;
+};
+
+static int max2175_set_freq_and_mode(struct max2175 *ctx, u32 freq)
+{
+	u32 rx_mode;
+	int ret;
+
+	/* Get band from frequency */
+	ret = max2175_rx_mode_from_freq(ctx, freq, &rx_mode);
+	if (ret)
+		return ret;
+
+	mxm_dbg(ctx, "set_freq_and_mode: freq %u rx_mode %d\n", freq, rx_mode);
+
+	/* Load mode */
+	max2175_set_rx_mode(ctx, rx_mode);
+	ctx->rx_mode->cur.val = rx_mode;
+
+	/* Tune to the new freq given */
+	return max2175_tune_rf_freq(ctx, freq, ctx->hsls->cur.val);
+}
+
+static int max2175_s_frequency(struct v4l2_subdev *sd,
+			       const struct v4l2_frequency *vf)
+{
+	struct max2175 *ctx = max2175_from_sd(sd);
+	u32 freq;
+	int ret = 0;
+
+	mxm_dbg(ctx, "s_freq: new %u curr %u, mode_resolved %d\n",
+		vf->frequency, ctx->freq, ctx->mode_resolved);
+
+	if (vf->tuner != 0)
+		return -EINVAL;
+
+	freq = clamp(vf->frequency, ctx->bands_rf->rangelow,
+		     ctx->bands_rf->rangehigh);
+
+	/* Check new freq valid for rx_mode if already resolved */
+	if (ctx->mode_resolved &&
+	    max2175_freq_rx_mode_valid(ctx, ctx->rx_mode->cur.val, freq))
+		ret = max2175_tune_rf_freq(ctx, freq, ctx->hsls->cur.val);
+	else
+		/* Find default rx_mode for freq and tune to it */
+		ret = max2175_set_freq_and_mode(ctx, freq);
+
+	mxm_dbg(ctx, "s_freq: ret %d curr %u mode_resolved %d mode %u\n",
+		ret, ctx->freq, ctx->mode_resolved, ctx->rx_mode->cur.val);
+
+	return ret;
+}
+
+static int max2175_g_frequency(struct v4l2_subdev *sd,
+			       struct v4l2_frequency *vf)
+{
+	struct max2175 *ctx = max2175_from_sd(sd);
+	int ret = 0;
+
+	if (vf->tuner != 0)
+		return -EINVAL;
+
+	/* RF freq */
+	vf->type = V4L2_TUNER_RF;
+	vf->frequency = ctx->freq;
+
+	return ret;
+}
+
+static int max2175_enum_freq_bands(struct v4l2_subdev *sd,
+			    struct v4l2_frequency_band *band)
+{
+	struct max2175 *ctx = max2175_from_sd(sd);
+
+	if (band->tuner != 0 || band->index != 0)
+		return -EINVAL;
+
+	*band = *ctx->bands_rf;
+
+	return 0;
+}
+
+static int max2175_g_tuner(struct v4l2_subdev *sd, struct v4l2_tuner *vt)
+{
+	struct max2175 *ctx = max2175_from_sd(sd);
+
+	if (vt->index > 0)
+		return -EINVAL;
+
+	strlcpy(vt->name, "RF", sizeof(vt->name));
+	vt->type = V4L2_TUNER_RF;
+	vt->capability = V4L2_TUNER_CAP_1HZ | V4L2_TUNER_CAP_FREQ_BANDS;
+	vt->rangelow = ctx->bands_rf->rangelow;
+	vt->rangehigh = ctx->bands_rf->rangehigh;
+
+	return 0;
+}
+
+static int max2175_s_tuner(struct v4l2_subdev *sd, const struct v4l2_tuner *vt)
+{
+	/* Check tuner index is valid */
+	if (vt->index > 0)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct v4l2_subdev_tuner_ops max2175_tuner_ops = {
+	.s_frequency = max2175_s_frequency,
+	.g_frequency = max2175_g_frequency,
+	.enum_freq_bands = max2175_enum_freq_bands,
+	.g_tuner = max2175_g_tuner,
+	.s_tuner = max2175_s_tuner,
+};
+
+static const struct v4l2_subdev_ops max2175_ops = {
+	.tuner = &max2175_tuner_ops,
+};
+
+static const struct v4l2_ctrl_ops max2175_ctrl_ops = {
+	.s_ctrl = max2175_s_ctrl,
+	.g_volatile_ctrl = max2175_g_volatile_ctrl,
+};
+
+static const struct v4l2_ctrl_config max2175_i2s_en = {
+	.ops = &max2175_ctrl_ops,
+	.id = V4L2_CID_MAX2175_I2S_ENABLE,
+	.name = "I2S Enable",
+	.type = V4L2_CTRL_TYPE_BOOLEAN,
+	.min = 0,
+	.max = 1,
+	.step = 1,
+	.def = 1,
+};
+
+/*
+ * HSLS value control LO freq adjacent location configuration.
+ * Refer to Documentation/media/v4l-drivers/max2175 for more details.
+ */
+static const struct v4l2_ctrl_config max2175_hsls = {
+	.ops = &max2175_ctrl_ops,
+	.id = V4L2_CID_MAX2175_HSLS,
+	.name = "HSLS Above/Below Desired",
+	.type = V4L2_CTRL_TYPE_BOOLEAN,
+	.min = 0,
+	.max = 1,
+	.step = 1,
+	.def = 1,
+};
+
+/*
+ * Rx modes below are a set of preset configurations that decides the tuner's
+ * sck and sample rate of transmission. They are separate for EU & NA regions.
+ * Refer to Documentation/media/v4l-drivers/max2175 for more details.
+ */
+static const char * const max2175_ctrl_eu_rx_modes[] = {
+	[MAX2175_EU_FM_1_2]	= "EU FM 1.2",
+	[MAX2175_DAB_1_2]	= "DAB 1.2",
+};
+
+static const char * const max2175_ctrl_na_rx_modes[] = {
+	[MAX2175_NA_FM_1_0]	= "NA FM 1.0",
+	[MAX2175_NA_FM_2_0]	= "NA FM 2.0",
+};
+
+static const struct v4l2_ctrl_config max2175_eu_rx_mode = {
+	.ops = &max2175_ctrl_ops,
+	.id = V4L2_CID_MAX2175_RX_MODE,
+	.name = "RX Mode",
+	.type = V4L2_CTRL_TYPE_MENU,
+	.max = ARRAY_SIZE(max2175_ctrl_eu_rx_modes) - 1,
+	.def = 0,
+	.qmenu = max2175_ctrl_eu_rx_modes,
+};
+
+static const struct v4l2_ctrl_config max2175_na_rx_mode = {
+	.ops = &max2175_ctrl_ops,
+	.id = V4L2_CID_MAX2175_RX_MODE,
+	.name = "RX Mode",
+	.type = V4L2_CTRL_TYPE_MENU,
+	.max = ARRAY_SIZE(max2175_ctrl_na_rx_modes) - 1,
+	.def = 0,
+	.qmenu = max2175_ctrl_na_rx_modes,
+};
+
+static int max2175_refout_load_to_bits(struct i2c_client *client, u32 load,
+				       u32 *bits)
+{
+	if (load >= 0 && load <= 40)
+		*bits = load / 10;
+	else if (load >= 60 && load <= 70)
+		*bits = load / 10 - 1;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static int max2175_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	bool master = true, am_hiz = false;
+	u32 refout_load, refout_bits = 0;	/* REFOUT disabled */
+	struct v4l2_ctrl_handler *hdl;
+	struct fwnode_handle *fwnode;
+	struct device_node *np;
+	struct v4l2_subdev *sd;
+	struct regmap *regmap;
+	struct max2175 *ctx;
+	struct clk *clk;
+	int ret;
+
+	/* Parse DT properties */
+	np = of_parse_phandle(client->dev.of_node, "maxim,master", 0);
+	if (np) {
+		master = false;			/* Slave tuner */
+		of_node_put(np);
+	}
+
+	fwnode = of_fwnode_handle(client->dev.of_node);
+	if (fwnode_property_present(fwnode, "maxim,am-hiz-filter"))
+		am_hiz = true;
+
+	if (!fwnode_property_read_u32(fwnode, "maxim,refout-load",
+				      &refout_load)) {
+		ret = max2175_refout_load_to_bits(client, refout_load,
+						  &refout_bits);
+		if (ret) {
+			dev_err(&client->dev, "invalid refout_load %u\n",
+				refout_load);
+			return -EINVAL;
+		}
+	}
+
+	clk = devm_clk_get(&client->dev, NULL);
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		dev_err(&client->dev, "cannot get clock %d\n", ret);
+		return -ENODEV;
+	}
+
+	regmap = devm_regmap_init_i2c(client, &max2175_regmap_config);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err(&client->dev, "regmap init failed %d\n", ret);
+		return -ENODEV;
+	}
+
+	/* Alloc tuner context */
+	ctx = devm_kzalloc(&client->dev, sizeof(*ctx), GFP_KERNEL);
+	if (ctx == NULL)
+		return -ENOMEM;
+
+	sd = &ctx->sd;
+	ctx->master = master;
+	ctx->am_hiz = am_hiz;
+	ctx->mode_resolved = false;
+	ctx->regmap = regmap;
+	ctx->xtal_freq = clk_get_rate(clk);
+	dev_info(&client->dev, "xtal freq %luHz\n", ctx->xtal_freq);
+
+	v4l2_i2c_subdev_init(sd, client, &max2175_ops);
+	ctx->client = client;
+
+	sd->flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	/* Controls */
+	hdl = &ctx->ctrl_hdl;
+	ret = v4l2_ctrl_handler_init(hdl, 7);
+	if (ret)
+		return ret;
+
+	ctx->lna_gain = v4l2_ctrl_new_std(hdl, &max2175_ctrl_ops,
+					  V4L2_CID_RF_TUNER_LNA_GAIN,
+					  0, 63, 1, 0);
+	ctx->lna_gain->flags |= (V4L2_CTRL_FLAG_VOLATILE |
+				 V4L2_CTRL_FLAG_READ_ONLY);
+	ctx->if_gain = v4l2_ctrl_new_std(hdl, &max2175_ctrl_ops,
+					 V4L2_CID_RF_TUNER_IF_GAIN,
+					 0, 31, 1, 0);
+	ctx->if_gain->flags |= (V4L2_CTRL_FLAG_VOLATILE |
+				V4L2_CTRL_FLAG_READ_ONLY);
+	ctx->pll_lock = v4l2_ctrl_new_std(hdl, &max2175_ctrl_ops,
+					  V4L2_CID_RF_TUNER_PLL_LOCK,
+					  0, 1, 1, 0);
+	ctx->pll_lock->flags |= (V4L2_CTRL_FLAG_VOLATILE |
+				 V4L2_CTRL_FLAG_READ_ONLY);
+	ctx->i2s_en = v4l2_ctrl_new_custom(hdl, &max2175_i2s_en, NULL);
+	ctx->hsls = v4l2_ctrl_new_custom(hdl, &max2175_hsls, NULL);
+
+	if (ctx->xtal_freq == MAX2175_EU_XTAL_FREQ) {
+		ctx->rx_mode = v4l2_ctrl_new_custom(hdl,
+						    &max2175_eu_rx_mode, NULL);
+		ctx->rx_modes = eu_rx_modes;
+		ctx->bands_rf = &eu_bands_rf;
+	} else {
+		ctx->rx_mode = v4l2_ctrl_new_custom(hdl,
+						    &max2175_na_rx_mode, NULL);
+		ctx->rx_modes = na_rx_modes;
+		ctx->bands_rf = &na_bands_rf;
+	}
+	ctx->sd.ctrl_handler = &ctx->ctrl_hdl;
+
+	/* Set the defaults */
+	ctx->freq = ctx->bands_rf->rangelow;
+
+	/* Register subdev */
+	ret = v4l2_async_register_subdev(sd);
+	if (ret) {
+		dev_err(&client->dev, "register subdev failed\n");
+		goto err_reg;
+	}
+
+	/* Initialize device */
+	ret = max2175_core_init(ctx, refout_bits);
+	if (ret)
+		goto err_init;
+
+	ret = v4l2_ctrl_handler_setup(hdl);
+	if (ret)
+		goto err_init;
+
+	return 0;
+
+err_init:
+	v4l2_async_unregister_subdev(sd);
+err_reg:
+	v4l2_ctrl_handler_free(&ctx->ctrl_hdl);
+
+	return ret;
+}
+
+static int max2175_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct max2175 *ctx = max2175_from_sd(sd);
+
+	v4l2_ctrl_handler_free(&ctx->ctrl_hdl);
+	v4l2_async_unregister_subdev(sd);
+
+	return 0;
+}
+
+static const struct i2c_device_id max2175_id[] = {
+	{ DRIVER_NAME, 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, max2175_id);
+
+static const struct of_device_id max2175_of_ids[] = {
+	{ .compatible = "maxim,max2175", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, max2175_of_ids);
+
+static struct i2c_driver max2175_driver = {
+	.driver = {
+		.name	= DRIVER_NAME,
+		.of_match_table = max2175_of_ids,
+	},
+	.probe		= max2175_probe,
+	.remove		= max2175_remove,
+	.id_table	= max2175_id,
+};
+
+module_i2c_driver(max2175_driver);
+
+MODULE_DESCRIPTION("Maxim MAX2175 RF to Bits tuner driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>");
diff --git a/drivers/media/i2c/max2175.h b/drivers/media/i2c/max2175.h
new file mode 100644
index 000000000000..072636f3660b
--- /dev/null
+++ b/drivers/media/i2c/max2175.h
@@ -0,0 +1,107 @@ 
+/*
+ * Maxim Integrated MAX2175 RF to Bits tuner driver
+ *
+ * This driver & most of the hard coded values are based on the reference
+ * application delivered by Maxim for this device.
+ *
+ * Copyright (C) 2016 Maxim Integrated Products
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MAX2175_H__
+#define __MAX2175_H__
+
+#define MAX2175_EU_XTAL_FREQ	36864000	/* In Hz */
+#define MAX2175_NA_XTAL_FREQ	40186125	/* In Hz */
+
+enum max2175_region {
+	MAX2175_REGION_EU = 0,	/* Europe */
+	MAX2175_REGION_NA,	/* North America */
+};
+
+enum max2175_band {
+	MAX2175_BAND_AM = 0,
+	MAX2175_BAND_FM,
+	MAX2175_BAND_VHF,
+	MAX2175_BAND_L,
+};
+
+enum max2175_eu_mode {
+	/* EU modes */
+	MAX2175_EU_FM_1_2 = 0,
+	MAX2175_DAB_1_2,
+
+	/* Other possible modes to add in future
+	 * MAX2175_DAB_1_0,
+	 * MAX2175_DAB_1_3,
+	 * MAX2175_EU_FM_2_2,
+	 * MAX2175_EU_FMHD_4_0,
+	 * MAX2175_EU_AM_1_0,
+	 * MAX2175_EU_AM_2_2,
+	 */
+};
+
+enum max2175_na_mode {
+	/* NA modes */
+	MAX2175_NA_FM_1_0 = 0,
+	MAX2175_NA_FM_2_0,
+
+	/* Other possible modes to add in future
+	 * MAX2175_NA_FMHD_1_0,
+	 * MAX2175_NA_FMHD_1_2,
+	 * MAX2175_NA_AM_1_0,
+	 * MAX2175_NA_AM_1_2,
+	 */
+};
+
+/* Supported I2S modes */
+enum {
+	MAX2175_I2S_MODE0 = 0,
+	MAX2175_I2S_MODE1,
+	MAX2175_I2S_MODE2,
+	MAX2175_I2S_MODE3,
+	MAX2175_I2S_MODE4,
+};
+
+/* Coefficient table groups */
+enum {
+	MAX2175_CH_MSEL = 0,
+	MAX2175_EQ_MSEL,
+	MAX2175_AA_MSEL,
+};
+
+/* HSLS LO injection polarity */
+enum {
+	MAX2175_LO_BELOW_DESIRED = 0,
+	MAX2175_LO_ABOVE_DESIRED,
+};
+
+/* Channel FSM modes */
+enum max2175_csm_mode {
+	MAX2175_LOAD_TO_BUFFER = 0,
+	MAX2175_PRESET_TUNE,
+	MAX2175_SEARCH,
+	MAX2175_AF_UPDATE,
+	MAX2175_JUMP_FAST_TUNE,
+	MAX2175_CHECK,
+	MAX2175_LOAD_AND_SWAP,
+	MAX2175_END,
+	MAX2175_BUFFER_PLUS_PRESET_TUNE,
+	MAX2175_BUFFER_PLUS_SEARCH,
+	MAX2175_BUFFER_PLUS_AF_UPDATE,
+	MAX2175_BUFFER_PLUS_JUMP_FAST_TUNE,
+	MAX2175_BUFFER_PLUS_CHECK,
+	MAX2175_BUFFER_PLUS_LOAD_AND_SWAP,
+	MAX2175_NO_ACTION
+};
+
+#endif /* __MAX2175_H__ */
diff --git a/include/uapi/linux/max2175.h b/include/uapi/linux/max2175.h
new file mode 100644
index 000000000000..3ef5d264440f
--- /dev/null
+++ b/include/uapi/linux/max2175.h
@@ -0,0 +1,28 @@ 
+/*
+ * max2175.h
+ *
+ * Maxim Integrated MAX2175 RF to Bits tuner driver - user space header file.
+ *
+ * Copyright (C) 2016 Maxim Integrated Products
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __UAPI_MAX2175_H_
+#define __UAPI_MAX2175_H_
+
+#include <linux/v4l2-controls.h>
+
+#define V4L2_CID_MAX2175_I2S_ENABLE	(V4L2_CID_USER_MAX217X_BASE + 0x01)
+#define V4L2_CID_MAX2175_HSLS		(V4L2_CID_USER_MAX217X_BASE + 0x02)
+#define V4L2_CID_MAX2175_RX_MODE	(V4L2_CID_USER_MAX217X_BASE + 0x03)
+
+#endif /* __UAPI_MAX2175_H_ */