[1/5] media: i2c: imx290: Add support for 2 data lanes
Commit Message
The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit
adds support for 2 lane mode in addition to the 4 lane and also
configuring the data lane settings in the driver based on system
configuration.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
drivers/media/i2c/imx290.c | 130 ++++++++++++++++++++++++++++++++++---
1 file changed, 121 insertions(+), 9 deletions(-)
Comments
Hi Manivannan,
Thanks for the patchset.
On Sat, Nov 30, 2019 at 12:35:37AM +0530, Manivannan Sadhasivam wrote:
> The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit
> adds support for 2 lane mode in addition to the 4 lane and also
> configuring the data lane settings in the driver based on system
> configuration.
>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
> drivers/media/i2c/imx290.c | 130 ++++++++++++++++++++++++++++++++++---
> 1 file changed, 121 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> index f7678e5a5d87..1d49910937fb 100644
> --- a/drivers/media/i2c/imx290.c
> +++ b/drivers/media/i2c/imx290.c
> @@ -25,7 +25,18 @@
> #define IMX290_STANDBY 0x3000
> #define IMX290_REGHOLD 0x3001
> #define IMX290_XMSTA 0x3002
> +#define IMX290_FR_FDG_SEL 0x3009
> #define IMX290_GAIN 0x3014
> +#define IMX290_HMAX_LOW 0x301c
> +#define IMX290_HMAX_HIGH 0x301d
> +#define IMX290_PHY_LANE_NUM 0x3407
> +#define IMX290_CSI_LANE_MODE 0x3443
> +
> +/* HMAX fields */
> +#define IMX290_HMAX_2_1920 0x1130
> +#define IMX290_HMAX_4_1920 0x0898
> +#define IMX290_HMAX_2_720 0x19C8
> +#define IMX290_HMAX_4_720 0x0CE4
>
> #define IMX290_DEFAULT_LINK_FREQ 445500000
>
> @@ -56,6 +67,7 @@ struct imx290 {
> struct device *dev;
> struct clk *xclk;
> struct regmap *regmap;
> + int nlanes;
You're using u8 for another small (unsigned) integer later. How about u8
here?
>
> struct v4l2_subdev sd;
> struct v4l2_fwnode_endpoint ep;
> @@ -89,14 +101,11 @@ static const struct regmap_config imx290_regmap_config = {
>
> static const struct imx290_regval imx290_global_init_settings[] = {
> { 0x3007, 0x00 },
> - { 0x3009, 0x00 },
> { 0x3018, 0x65 },
> { 0x3019, 0x04 },
> { 0x301a, 0x00 },
> - { 0x3443, 0x03 },
> { 0x3444, 0x20 },
> { 0x3445, 0x25 },
> - { 0x3407, 0x03 },
> { 0x303a, 0x0c },
> { 0x3040, 0x00 },
> { 0x3041, 0x00 },
> @@ -169,7 +178,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
> { 0x3164, 0x1a },
> { 0x3480, 0x49 },
> /* data rate settings */
> - { 0x3009, 0x01 },
> { 0x3405, 0x10 },
> { 0x3446, 0x57 },
> { 0x3447, 0x00 },
> @@ -187,8 +195,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
> { 0x3453, 0x00 },
> { 0x3454, 0x17 },
> { 0x3455, 0x00 },
> - { 0x301c, 0x98 },
> - { 0x301d, 0x08 },
> };
>
> static const struct imx290_regval imx290_720p_settings[] = {
> @@ -210,7 +216,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
> { 0x3164, 0x1a },
> { 0x3480, 0x49 },
> /* data rate settings */
> - { 0x3009, 0x01 },
> { 0x3405, 0x10 },
> { 0x3446, 0x4f },
> { 0x3447, 0x00 },
> @@ -228,8 +233,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
> { 0x3453, 0x00 },
> { 0x3454, 0x17 },
> { 0x3455, 0x00 },
> - { 0x301c, 0xe4 },
> - { 0x301d, 0x0c },
> };
>
> static const struct imx290_regval imx290_10bit_settings[] = {
> @@ -522,6 +525,25 @@ static int imx290_write_current_format(struct imx290 *imx290,
> return 0;
> }
>
> +static int imx290_set_hmax(struct imx290 *imx290, u32 val)
> +{
> + int ret;
> +
> + ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff));
> + if (ret) {
> + dev_err(imx290->dev, "Error setting HMAX register\n");
> + return ret;
> + }
> +
> + ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff));
> + if (ret) {
> + dev_err(imx290->dev, "Error setting HMAX register\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> /* Start streaming */
> static int imx290_start_streaming(struct imx290 *imx290)
> {
> @@ -551,6 +573,40 @@ static int imx290_start_streaming(struct imx290 *imx290)
> return ret;
> }
>
> + switch (imx290->nlanes) {
> + case 2:
> + if (imx290->current_mode->width == 1920) {
> + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_1920);
> + if (ret < 0)
> + return ret;
> + } else {
> + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_720);
> + if (ret < 0)
> + return ret;
> + }
> +
> + break;
> + case 4:
> + if (imx290->current_mode->width == 1920) {
> + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_1920);
> + if (ret < 0)
> + return ret;
> + } else {
> + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_720);
> + if (ret < 0)
> + return ret;
> + }
> +
> + break;
> + default:
> + /*
> + * We should never hit this since the data lane count is
> + * validated in probe itself
> + */
> + dev_err(imx290->dev, "Lane configuration not supported\n");
> + return -EINVAL;
> + }
> +
> /* Apply customized values from user */
> ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler);
> if (ret) {
> @@ -607,6 +663,49 @@ static int imx290_get_regulators(struct device *dev, struct imx290 *imx290)
> imx290->supplies);
> }
>
> +static int imx290_set_data_lanes(struct imx290 *imx290)
> +{
> + int ret = 0, laneval, frsel;
> +
> + switch (imx290->nlanes) {
> + case 2:
> + laneval = 0x01;
> + frsel = 0x02;
> + break;
> + case 4:
> + laneval = 0x03;
> + frsel = 0x01;
> + break;
> + default:
> + /*
> + * We should never hit this since the data lane count is
> + * validated in probe itself
> + */
> + dev_err(imx290->dev, "Lane configuration not supported\n");
> + ret = -EINVAL;
> + goto exit;
> + }
> +
> + ret = imx290_write_reg(imx290, IMX290_PHY_LANE_NUM, laneval);
> + if (ret) {
> + dev_err(imx290->dev, "Error setting Physical Lane number register\n");
> + goto exit;
> + }
> +
> + ret = imx290_write_reg(imx290, IMX290_CSI_LANE_MODE, laneval);
> + if (ret) {
> + dev_err(imx290->dev, "Error setting CSI Lane mode register\n");
> + goto exit;
> + }
> +
> + ret = imx290_write_reg(imx290, IMX290_FR_FDG_SEL, frsel);
> + if (ret)
> + dev_err(imx290->dev, "Error setting FR/FDG SEL register\n");
> +
> +exit:
> + return ret;
> +}
> +
> static int imx290_power_on(struct device *dev)
> {
> struct i2c_client *client = to_i2c_client(dev);
> @@ -703,6 +802,16 @@ static int imx290_probe(struct i2c_client *client)
> goto free_err;
> }
>
> + /* Get number of data lanes */
> + imx290->nlanes = imx290->ep.bus.mipi_csi2.num_data_lanes;
> + if (imx290->nlanes != 2 && imx290->nlanes != 4) {
> + dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes);
> + ret = -EINVAL;
> + goto free_err;
> + }
> +
> + dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes);
> +
> if (!imx290->ep.nr_of_link_frequencies) {
> dev_err(dev, "link-frequency property not found in DT\n");
> ret = -EINVAL;
> @@ -822,6 +931,9 @@ static int imx290_probe(struct i2c_client *client)
> goto free_entity;
> }
>
> + /* Set data lane count */
> + imx290_set_data_lanes(imx290);
The sensor is likely (but not necessarily) about to be powered off here.
Wouldn't this also belong to be put to the power on sequence?
> +
> pm_runtime_set_active(dev);
> pm_runtime_enable(dev);
> pm_runtime_idle(dev);
Hi Sakari,
On Tue, Dec 03, 2019 at 10:45:20AM +0200, Sakari Ailus wrote:
> Hi Manivannan,
>
> Thanks for the patchset.
>
> On Sat, Nov 30, 2019 at 12:35:37AM +0530, Manivannan Sadhasivam wrote:
> > The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit
> > adds support for 2 lane mode in addition to the 4 lane and also
> > configuring the data lane settings in the driver based on system
> > configuration.
> >
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> > drivers/media/i2c/imx290.c | 130 ++++++++++++++++++++++++++++++++++---
> > 1 file changed, 121 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> > index f7678e5a5d87..1d49910937fb 100644
> > --- a/drivers/media/i2c/imx290.c
> > +++ b/drivers/media/i2c/imx290.c
> > @@ -25,7 +25,18 @@
> > #define IMX290_STANDBY 0x3000
> > #define IMX290_REGHOLD 0x3001
> > #define IMX290_XMSTA 0x3002
> > +#define IMX290_FR_FDG_SEL 0x3009
> > #define IMX290_GAIN 0x3014
> > +#define IMX290_HMAX_LOW 0x301c
> > +#define IMX290_HMAX_HIGH 0x301d
> > +#define IMX290_PHY_LANE_NUM 0x3407
> > +#define IMX290_CSI_LANE_MODE 0x3443
> > +
> > +/* HMAX fields */
> > +#define IMX290_HMAX_2_1920 0x1130
> > +#define IMX290_HMAX_4_1920 0x0898
> > +#define IMX290_HMAX_2_720 0x19C8
> > +#define IMX290_HMAX_4_720 0x0CE4
> >
> > #define IMX290_DEFAULT_LINK_FREQ 445500000
> >
> > @@ -56,6 +67,7 @@ struct imx290 {
> > struct device *dev;
> > struct clk *xclk;
> > struct regmap *regmap;
> > + int nlanes;
>
> You're using u8 for another small (unsigned) integer later. How about u8
> here?
>
Yeah, this is a left over. I was initially trying to use some error
checking with this! Will change it to u8.
> >
> > struct v4l2_subdev sd;
> > struct v4l2_fwnode_endpoint ep;
> > @@ -89,14 +101,11 @@ static const struct regmap_config imx290_regmap_config = {
> >
> > static const struct imx290_regval imx290_global_init_settings[] = {
> > { 0x3007, 0x00 },
> > - { 0x3009, 0x00 },
> > { 0x3018, 0x65 },
> > { 0x3019, 0x04 },
> > { 0x301a, 0x00 },
> > - { 0x3443, 0x03 },
> > { 0x3444, 0x20 },
> > { 0x3445, 0x25 },
> > - { 0x3407, 0x03 },
> > { 0x303a, 0x0c },
> > { 0x3040, 0x00 },
> > { 0x3041, 0x00 },
> > @@ -169,7 +178,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
> > { 0x3164, 0x1a },
> > { 0x3480, 0x49 },
> > /* data rate settings */
> > - { 0x3009, 0x01 },
> > { 0x3405, 0x10 },
> > { 0x3446, 0x57 },
> > { 0x3447, 0x00 },
> > @@ -187,8 +195,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
> > { 0x3453, 0x00 },
> > { 0x3454, 0x17 },
> > { 0x3455, 0x00 },
> > - { 0x301c, 0x98 },
> > - { 0x301d, 0x08 },
> > };
> >
> > static const struct imx290_regval imx290_720p_settings[] = {
> > @@ -210,7 +216,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
> > { 0x3164, 0x1a },
> > { 0x3480, 0x49 },
> > /* data rate settings */
> > - { 0x3009, 0x01 },
> > { 0x3405, 0x10 },
> > { 0x3446, 0x4f },
> > { 0x3447, 0x00 },
> > @@ -228,8 +233,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
> > { 0x3453, 0x00 },
> > { 0x3454, 0x17 },
> > { 0x3455, 0x00 },
> > - { 0x301c, 0xe4 },
> > - { 0x301d, 0x0c },
> > };
> >
> > static const struct imx290_regval imx290_10bit_settings[] = {
> > @@ -522,6 +525,25 @@ static int imx290_write_current_format(struct imx290 *imx290,
> > return 0;
> > }
> >
> > +static int imx290_set_hmax(struct imx290 *imx290, u32 val)
> > +{
> > + int ret;
> > +
> > + ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff));
> > + if (ret) {
> > + dev_err(imx290->dev, "Error setting HMAX register\n");
> > + return ret;
> > + }
> > +
> > + ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff));
> > + if (ret) {
> > + dev_err(imx290->dev, "Error setting HMAX register\n");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > /* Start streaming */
> > static int imx290_start_streaming(struct imx290 *imx290)
> > {
> > @@ -551,6 +573,40 @@ static int imx290_start_streaming(struct imx290 *imx290)
> > return ret;
> > }
> >
> > + switch (imx290->nlanes) {
> > + case 2:
> > + if (imx290->current_mode->width == 1920) {
> > + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_1920);
> > + if (ret < 0)
> > + return ret;
> > + } else {
> > + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_720);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + break;
> > + case 4:
> > + if (imx290->current_mode->width == 1920) {
> > + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_1920);
> > + if (ret < 0)
> > + return ret;
> > + } else {
> > + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_720);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + break;
> > + default:
> > + /*
> > + * We should never hit this since the data lane count is
> > + * validated in probe itself
> > + */
> > + dev_err(imx290->dev, "Lane configuration not supported\n");
> > + return -EINVAL;
> > + }
> > +
> > /* Apply customized values from user */
> > ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler);
> > if (ret) {
> > @@ -607,6 +663,49 @@ static int imx290_get_regulators(struct device *dev, struct imx290 *imx290)
> > imx290->supplies);
> > }
> >
> > +static int imx290_set_data_lanes(struct imx290 *imx290)
> > +{
> > + int ret = 0, laneval, frsel;
> > +
> > + switch (imx290->nlanes) {
> > + case 2:
> > + laneval = 0x01;
> > + frsel = 0x02;
> > + break;
> > + case 4:
> > + laneval = 0x03;
> > + frsel = 0x01;
> > + break;
> > + default:
> > + /*
> > + * We should never hit this since the data lane count is
> > + * validated in probe itself
> > + */
> > + dev_err(imx290->dev, "Lane configuration not supported\n");
> > + ret = -EINVAL;
> > + goto exit;
> > + }
> > +
> > + ret = imx290_write_reg(imx290, IMX290_PHY_LANE_NUM, laneval);
> > + if (ret) {
> > + dev_err(imx290->dev, "Error setting Physical Lane number register\n");
> > + goto exit;
> > + }
> > +
> > + ret = imx290_write_reg(imx290, IMX290_CSI_LANE_MODE, laneval);
> > + if (ret) {
> > + dev_err(imx290->dev, "Error setting CSI Lane mode register\n");
> > + goto exit;
> > + }
> > +
> > + ret = imx290_write_reg(imx290, IMX290_FR_FDG_SEL, frsel);
> > + if (ret)
> > + dev_err(imx290->dev, "Error setting FR/FDG SEL register\n");
> > +
> > +exit:
> > + return ret;
> > +}
> > +
> > static int imx290_power_on(struct device *dev)
> > {
> > struct i2c_client *client = to_i2c_client(dev);
> > @@ -703,6 +802,16 @@ static int imx290_probe(struct i2c_client *client)
> > goto free_err;
> > }
> >
> > + /* Get number of data lanes */
> > + imx290->nlanes = imx290->ep.bus.mipi_csi2.num_data_lanes;
> > + if (imx290->nlanes != 2 && imx290->nlanes != 4) {
> > + dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes);
> > + ret = -EINVAL;
> > + goto free_err;
> > + }
> > +
> > + dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes);
> > +
> > if (!imx290->ep.nr_of_link_frequencies) {
> > dev_err(dev, "link-frequency property not found in DT\n");
> > ret = -EINVAL;
> > @@ -822,6 +931,9 @@ static int imx290_probe(struct i2c_client *client)
> > goto free_entity;
> > }
> >
> > + /* Set data lane count */
> > + imx290_set_data_lanes(imx290);
>
> The sensor is likely (but not necessarily) about to be powered off here.
> Wouldn't this also belong to be put to the power on sequence?
>
Agree, will add.
Thanks,
Mani
> > +
> > pm_runtime_set_active(dev);
> > pm_runtime_enable(dev);
> > pm_runtime_idle(dev);
>
> --
> Regards,
>
> Sakari Ailus
@@ -25,7 +25,18 @@
#define IMX290_STANDBY 0x3000
#define IMX290_REGHOLD 0x3001
#define IMX290_XMSTA 0x3002
+#define IMX290_FR_FDG_SEL 0x3009
#define IMX290_GAIN 0x3014
+#define IMX290_HMAX_LOW 0x301c
+#define IMX290_HMAX_HIGH 0x301d
+#define IMX290_PHY_LANE_NUM 0x3407
+#define IMX290_CSI_LANE_MODE 0x3443
+
+/* HMAX fields */
+#define IMX290_HMAX_2_1920 0x1130
+#define IMX290_HMAX_4_1920 0x0898
+#define IMX290_HMAX_2_720 0x19C8
+#define IMX290_HMAX_4_720 0x0CE4
#define IMX290_DEFAULT_LINK_FREQ 445500000
@@ -56,6 +67,7 @@ struct imx290 {
struct device *dev;
struct clk *xclk;
struct regmap *regmap;
+ int nlanes;
struct v4l2_subdev sd;
struct v4l2_fwnode_endpoint ep;
@@ -89,14 +101,11 @@ static const struct regmap_config imx290_regmap_config = {
static const struct imx290_regval imx290_global_init_settings[] = {
{ 0x3007, 0x00 },
- { 0x3009, 0x00 },
{ 0x3018, 0x65 },
{ 0x3019, 0x04 },
{ 0x301a, 0x00 },
- { 0x3443, 0x03 },
{ 0x3444, 0x20 },
{ 0x3445, 0x25 },
- { 0x3407, 0x03 },
{ 0x303a, 0x0c },
{ 0x3040, 0x00 },
{ 0x3041, 0x00 },
@@ -169,7 +178,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
{ 0x3164, 0x1a },
{ 0x3480, 0x49 },
/* data rate settings */
- { 0x3009, 0x01 },
{ 0x3405, 0x10 },
{ 0x3446, 0x57 },
{ 0x3447, 0x00 },
@@ -187,8 +195,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
{ 0x3453, 0x00 },
{ 0x3454, 0x17 },
{ 0x3455, 0x00 },
- { 0x301c, 0x98 },
- { 0x301d, 0x08 },
};
static const struct imx290_regval imx290_720p_settings[] = {
@@ -210,7 +216,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
{ 0x3164, 0x1a },
{ 0x3480, 0x49 },
/* data rate settings */
- { 0x3009, 0x01 },
{ 0x3405, 0x10 },
{ 0x3446, 0x4f },
{ 0x3447, 0x00 },
@@ -228,8 +233,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
{ 0x3453, 0x00 },
{ 0x3454, 0x17 },
{ 0x3455, 0x00 },
- { 0x301c, 0xe4 },
- { 0x301d, 0x0c },
};
static const struct imx290_regval imx290_10bit_settings[] = {
@@ -522,6 +525,25 @@ static int imx290_write_current_format(struct imx290 *imx290,
return 0;
}
+static int imx290_set_hmax(struct imx290 *imx290, u32 val)
+{
+ int ret;
+
+ ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff));
+ if (ret) {
+ dev_err(imx290->dev, "Error setting HMAX register\n");
+ return ret;
+ }
+
+ ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff));
+ if (ret) {
+ dev_err(imx290->dev, "Error setting HMAX register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
/* Start streaming */
static int imx290_start_streaming(struct imx290 *imx290)
{
@@ -551,6 +573,40 @@ static int imx290_start_streaming(struct imx290 *imx290)
return ret;
}
+ switch (imx290->nlanes) {
+ case 2:
+ if (imx290->current_mode->width == 1920) {
+ ret = imx290_set_hmax(imx290, IMX290_HMAX_2_1920);
+ if (ret < 0)
+ return ret;
+ } else {
+ ret = imx290_set_hmax(imx290, IMX290_HMAX_2_720);
+ if (ret < 0)
+ return ret;
+ }
+
+ break;
+ case 4:
+ if (imx290->current_mode->width == 1920) {
+ ret = imx290_set_hmax(imx290, IMX290_HMAX_4_1920);
+ if (ret < 0)
+ return ret;
+ } else {
+ ret = imx290_set_hmax(imx290, IMX290_HMAX_4_720);
+ if (ret < 0)
+ return ret;
+ }
+
+ break;
+ default:
+ /*
+ * We should never hit this since the data lane count is
+ * validated in probe itself
+ */
+ dev_err(imx290->dev, "Lane configuration not supported\n");
+ return -EINVAL;
+ }
+
/* Apply customized values from user */
ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler);
if (ret) {
@@ -607,6 +663,49 @@ static int imx290_get_regulators(struct device *dev, struct imx290 *imx290)
imx290->supplies);
}
+static int imx290_set_data_lanes(struct imx290 *imx290)
+{
+ int ret = 0, laneval, frsel;
+
+ switch (imx290->nlanes) {
+ case 2:
+ laneval = 0x01;
+ frsel = 0x02;
+ break;
+ case 4:
+ laneval = 0x03;
+ frsel = 0x01;
+ break;
+ default:
+ /*
+ * We should never hit this since the data lane count is
+ * validated in probe itself
+ */
+ dev_err(imx290->dev, "Lane configuration not supported\n");
+ ret = -EINVAL;
+ goto exit;
+ }
+
+ ret = imx290_write_reg(imx290, IMX290_PHY_LANE_NUM, laneval);
+ if (ret) {
+ dev_err(imx290->dev, "Error setting Physical Lane number register\n");
+ goto exit;
+ }
+
+ ret = imx290_write_reg(imx290, IMX290_CSI_LANE_MODE, laneval);
+ if (ret) {
+ dev_err(imx290->dev, "Error setting CSI Lane mode register\n");
+ goto exit;
+ }
+
+ ret = imx290_write_reg(imx290, IMX290_FR_FDG_SEL, frsel);
+ if (ret)
+ dev_err(imx290->dev, "Error setting FR/FDG SEL register\n");
+
+exit:
+ return ret;
+}
+
static int imx290_power_on(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
@@ -703,6 +802,16 @@ static int imx290_probe(struct i2c_client *client)
goto free_err;
}
+ /* Get number of data lanes */
+ imx290->nlanes = imx290->ep.bus.mipi_csi2.num_data_lanes;
+ if (imx290->nlanes != 2 && imx290->nlanes != 4) {
+ dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes);
+ ret = -EINVAL;
+ goto free_err;
+ }
+
+ dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes);
+
if (!imx290->ep.nr_of_link_frequencies) {
dev_err(dev, "link-frequency property not found in DT\n");
ret = -EINVAL;
@@ -822,6 +931,9 @@ static int imx290_probe(struct i2c_client *client)
goto free_entity;
}
+ /* Set data lane count */
+ imx290_set_data_lanes(imx290);
+
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
pm_runtime_idle(dev);