[12/12,RFC] media: dw9719: Drop hack to enable "vsio" regulator
Commit Message
Drop the hack where the driver is getting + enabling a "vsio" regulator
even though the dw9719 does not have a vsio pin / power-plane at all.
Now that drivers/media/common/intel-cio2-bridge.c adds device-link
making the VCM a consumer of the sensor this hack is no longer necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Note to reviewers, the dw9719 driver is not upstream yet (I plan to
resubmit it soon with this squashed in). This patch is only included
in this patch-set to illustrate how the VCM -> sensor device-link
avoids the need for hacks like this.
---
drivers/media/i2c/dw9719.c | 27 +++++++--------------------
1 file changed, 7 insertions(+), 20 deletions(-)
@@ -35,14 +35,12 @@
#define DW9719_DEFAULT_VCM_FREQ 0x60
#define DW9719_ENABLE_RINGING 0x02
-#define NUM_REGULATORS 2
-
#define to_dw9719_device(x) container_of(x, struct dw9719_device, sd)
struct dw9719_device {
struct device *dev;
struct i2c_client *client;
- struct regulator_bulk_data regulators[NUM_REGULATORS];
+ struct regulator *regulator;
struct v4l2_subdev sd;
struct dw9719_v4l2_ctrls {
@@ -131,14 +129,14 @@ static int dw9719_detect(struct dw9719_device *dw9719)
static int dw9719_power_down(struct dw9719_device *dw9719)
{
- return regulator_bulk_disable(NUM_REGULATORS, dw9719->regulators);
+ return regulator_disable(dw9719->regulator);
}
static int dw9719_power_up(struct dw9719_device *dw9719)
{
int ret;
- ret = regulator_bulk_enable(NUM_REGULATORS, dw9719->regulators);
+ ret = regulator_enable(dw9719->regulator);
if (ret)
return ret;
@@ -315,21 +313,10 @@ static int dw9719_probe(struct i2c_client *client)
dw9719->client = client;
dw9719->dev = &client->dev;
- dw9719->regulators[0].supply = "vdd";
- /*
- * The DW9719 has only the 1 VDD voltage input, but some PMICs such as
- * the TPS68470 PMIC have I2C passthrough capability, to disconnect the
- * sensor's I2C pins from the I2C bus when the sensors VSIO (Sensor-IO)
- * is off, because some sensors then short these pins to ground;
- * and the DW9719 might sit behind this passthrough, this it needs to
- * enable VSIO as that will also enable the I2C passthrough.
- */
- dw9719->regulators[1].supply = "vsio";
-
- ret = devm_regulator_bulk_get(&client->dev, NUM_REGULATORS,
- dw9719->regulators);
- if (ret)
- return dev_err_probe(&client->dev, ret, "getting regulators\n");
+ dw9719->regulator = devm_regulator_get(&client->dev, "vdd");
+ if (IS_ERR(dw9719->regulator))
+ return dev_err_probe(&client->dev, PTR_ERR(dw9719->regulator),
+ "getting regulator\n");
v4l2_i2c_subdev_init(&dw9719->sd, client, &dw9719_ops);
dw9719->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;