Message ID | 201204071924.44679.hfvogt@gmx.net (mailing list archive) |
---|---|
State | Superseded, archived |
Headers |
Received: from mail.tu-berlin.de ([130.149.7.33]) by www.linuxtv.org with esmtp (Exim 4.72) (envelope-from <linux-media-owner@vger.kernel.org>) id 1SGZjB-0003xu-7o for patchwork@linuxtv.org; Sat, 07 Apr 2012 19:47:09 +0200 X-tubIT-Incoming-IP: 209.132.180.67 Received: from vger.kernel.org ([209.132.180.67]) by mail.tu-berlin.de (exim-4.75/mailfrontend-2) with esmtp for <patchwork@linuxtv.org> id 1SGZjA-000653-I7; Sat, 07 Apr 2012 19:47:09 +0200 Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753319Ab2DGRrG (ORCPT <rfc822;patchwork@linuxtv.org>); Sat, 7 Apr 2012 13:47:06 -0400 Received: from mailout-de.gmx.net ([213.165.64.22]:41634 "HELO mailout-de.gmx.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with SMTP id S1752375Ab2DGRrF (ORCPT <rfc822; linux-media@vger.kernel.org>); Sat, 7 Apr 2012 13:47:05 -0400 Received: (qmail invoked by alias); 07 Apr 2012 17:24:50 -0000 Received: from p4FC08728.dip0.t-ipconnect.de (EHLO maximilian.localnet) [79.192.135.40] by mail.gmx.net (mp002) with SMTP; 07 Apr 2012 19:24:50 +0200 X-Authenticated: #24390674 X-Provags-ID: V01U2FsdGVkX18b8ddCKT0b/V0MZT/+8nJ+h1yKE/PWeRHoMRtfzR t640Sd3CZno8WC From: "Hans-Frieder Vogt" <hfvogt@gmx.net> To: Antti Palosaari <crope@iki.fi> Subject: [PATCH] af9035: add remote control support Date: Sat, 7 Apr 2012 19:24:44 +0200 User-Agent: KMail/1.13.7 (Linux/3.3.1-a64; KDE/4.7.4; x86_64; ; ) Cc: linux-media@vger.kernel.org, Michael =?iso-8859-1?q?B=FCsch?= <m@bues.ch>, Gianluca Gennari <gennarone@gmail.com> MIME-Version: 1.0 Content-Type: Text/Plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Message-Id: <201204071924.44679.hfvogt@gmx.net> X-Y-GMX-Trusted: 0 Sender: linux-media-owner@vger.kernel.org Precedence: bulk List-ID: <linux-media.vger.kernel.org> X-Mailing-List: linux-media@vger.kernel.org X-PMX-Version: 5.6.1.2065439, Antispam-Engine: 2.7.2.376379, Antispam-Data: 2012.4.7.173041 X-PMX-Spam: Gauge=IIIIIIII, Probability=8%, Report=' MULTIPLE_RCPTS 0.1, HTML_00_01 0.05, HTML_00_10 0.05, BODY_SIZE_3000_3999 0, BODY_SIZE_5000_LESS 0, BODY_SIZE_7000_LESS 0, URI_ENDS_IN_HTML 0, __ANY_URI 0, __CP_URI_IN_BODY 0, __CT 0, __CTE 0, __CT_TEXT_PLAIN 0, __HAS_MSGID 0, __HAS_X_MAILING_LIST 0, __MIME_TEXT_ONLY 0, __MIME_VERSION 0, __MULTIPLE_RCPTS_CC_X2 0, __SANE_MSGID 0, __STOCK_PHRASE_7 0, __SUBJ_ALPHA_END 0, __TO_MALFORMED_2 0, __URI_NO_WWW 0, __URI_NS , __USER_AGENT 0' |
Commit Message
Hans-Frieder Vogt
April 7, 2012, 5:24 p.m. UTC
af9035: support remote controls. Currently, for remotes using the NEC protocol,
the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 the map of
RC_MAP_RC6_MCE.
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
drivers/media/dvb/dvb-usb/af9035.c | 72 +++++++++++++++++++++++++++++++++++++
drivers/media/dvb/dvb-usb/af9035.h | 3 +
2 files changed, 75 insertions(+)
Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Comments
Em 07-04-2012 14:24, Hans-Frieder Vogt escreveu: > af9035: support remote controls. Currently, for remotes using the NEC protocol, > the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 the map of > RC_MAP_RC6_MCE. > > Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net> > > drivers/media/dvb/dvb-usb/af9035.c | 72 +++++++++++++++++++++++++++++++++++++ > drivers/media/dvb/dvb-usb/af9035.h | 3 + > 2 files changed, 75 insertions(+) > > diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c b/drivers/media/dvb/dvb-usb/af9035.c > --- a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 +0200 > +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 19:17:55.044874329 +0200 > @@ -313,6 +313,41 @@ static struct i2c_algorithm af9035_i2c_a > .functionality = af9035_i2c_functionality, > }; > > +#define AF9035_POLL 250 > +static int af9035_rc_query(struct dvb_usb_device *d) > +{ > + unsigned int key; > + unsigned char b[4]; > + int ret; > + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; > + > + if (!af9035_config.raw_ir) > + return 0; > + > + ret = af9035_ctrl_msg(d->udev, &req); > + if (ret < 0) > + goto err; > + > + if ((b[2] + b[3]) == 0xff) { > + if ((b[0] + b[1]) == 0xff) { > + /* NEC */ > + key = b[0] << 8 | b[2]; > + } else { > + /* ext. NEC */ > + key = b[0] << 16 | b[1] << 8 | b[2]; > + } > + } else { > + key = b[0] << 24 | b[1] << 16 | b[2] << 8 | b[3]; > + } > + > + if (d->rc_dev != NULL) > + rc_keydown(d->rc_dev, key, 0); > + > +err: > + /* ignore errors */ > + return 0; > +} > + > static int af9035_init(struct dvb_usb_device *d) > { > int ret, i; > @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc > for (i = 0; i < af9035_properties[0].num_adapters; i++) > af9035_af9033_config[i].clock = clock_lut[tmp]; > > + ret = af9035_rd_reg(d, EEPROM_IR_MODE, &tmp); > + if (ret < 0) > + goto err; > + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); > + af9035_config.raw_ir = tmp == 5; > + > + if (af9035_config.raw_ir) { > + ret = af9035_rd_reg(d, EEPROM_IR_TYPE, &tmp); > + if (ret < 0) > + goto err; > + pr_debug("%s: ir_type=%02x\n", __func__, tmp); > + > + switch (tmp) { > + case 0: /* NEC */ > + default: > + af9035_config.ir_rc6 = false; > + d->props.rc.core.protocol = RC_TYPE_NEC; > + d->props.rc.core.rc_codes = > + RC_MAP_NEC_TERRATEC_CINERGY_XS; > + break; > + case 1: /* RC6 */ > + af9035_config.ir_rc6 = true; > + d->props.rc.core.protocol = RC_TYPE_RC6; > + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; > + break; > + } > + } > + > return 0; > > err: > @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties > > .i2c_algo = &af9035_i2c_algo, > > + .rc.core = { > + .protocol = RC_TYPE_NEC, > + .module_name = "af9035", > + .rc_query = af9035_rc_query, > + .rc_interval = AF9035_POLL, > + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, > + .rc_codes = RC_MAP_EMPTY, /* may be changed in > + af9035_read_mac_address */ This is just a minor thing, but the comment here seems to be outdated, as this is actually set at af9035_init(). > + }, > .num_device_descs = 5, > .devices = { > { > diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h b/drivers/media/dvb/dvb-usb/af9035.h > --- a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 +0200 > +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 17:35:08.517840044 +0200 > @@ -49,6 +49,8 @@ struct usb_req { > > struct config { > bool dual_mode; > + bool raw_ir; > + bool ir_rc6; > bool hw_not_supported; > }; > > @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { > #define CMD_MEM_WR 0x01 > #define CMD_I2C_RD 0x02 > #define CMD_I2C_WR 0x03 > +#define CMD_IR_GET 0x18 > #define CMD_FW_DL 0x21 > #define CMD_FW_QUERYINFO 0x22 > #define CMD_FW_BOOT 0x23 > > Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net Except for that minor mistake at the comment above, the rest looks fine on my eyes. > -- > To unsubscribe from this list: send the line "unsubscribe linux-media" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
I haven't tried to and not commented it. But I see clearly few problems. On 18.04.2012 17:17, Mauro Carvalho Chehab wrote: > Em 07-04-2012 14:24, Hans-Frieder Vogt escreveu: >> af9035: support remote controls. Currently, for remotes using the NEC protocol, >> the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 the map of >> RC_MAP_RC6_MCE. >> >> Signed-off-by: Hans-Frieder Vogt<hfvogt@gmx.net> >> >> drivers/media/dvb/dvb-usb/af9035.c | 72 +++++++++++++++++++++++++++++++++++++ >> drivers/media/dvb/dvb-usb/af9035.h | 3 + >> 2 files changed, 75 insertions(+) >> >> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c b/drivers/media/dvb/dvb-usb/af9035.c >> --- a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 +0200 >> +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 19:17:55.044874329 +0200 >> @@ -313,6 +313,41 @@ static struct i2c_algorithm af9035_i2c_a >> .functionality = af9035_i2c_functionality, >> }; >> >> +#define AF9035_POLL 250 >> +static int af9035_rc_query(struct dvb_usb_device *d) >> +{ >> + unsigned int key; >> + unsigned char b[4]; >> + int ret; >> + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; >> + >> + if (!af9035_config.raw_ir) >> + return 0; >> + >> + ret = af9035_ctrl_msg(d->udev,&req); >> + if (ret< 0) >> + goto err; >> + >> + if ((b[2] + b[3]) == 0xff) { >> + if ((b[0] + b[1]) == 0xff) { >> + /* NEC */ >> + key = b[0]<< 8 | b[2]; >> + } else { >> + /* ext. NEC */ >> + key = b[0]<< 16 | b[1]<< 8 | b[2]; >> + } >> + } else { >> + key = b[0]<< 24 | b[1]<< 16 | b[2]<< 8 | b[3]; >> + } >> + >> + if (d->rc_dev != NULL) >> + rc_keydown(d->rc_dev, key, 0); Is that checking needed and why? If there is no rc_device why we even call poll for it? Better to fix some core routines if that is true. Also rc_keydown() takes 2nd param as int, but in that case it does not matter. Anyhow, 3rd param is toggle which is used by RC5/6. IIRC I have never implemented RC5 or RC6 remote receiver, so I am not sure if it is needed and in which case. >> + >> +err: >> + /* ignore errors */ >> + return 0; >> +} >> + >> static int af9035_init(struct dvb_usb_device *d) >> { >> int ret, i; >> @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc >> for (i = 0; i< af9035_properties[0].num_adapters; i++) >> af9035_af9033_config[i].clock = clock_lut[tmp]; >> >> + ret = af9035_rd_reg(d, EEPROM_IR_MODE,&tmp); >> + if (ret< 0) >> + goto err; >> + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); >> + af9035_config.raw_ir = tmp == 5; This looks odd for my eyes. Maybe x = (y == z); is better. Checkpatch didn't complain it? >> + >> + if (af9035_config.raw_ir) { >> + ret = af9035_rd_reg(d, EEPROM_IR_TYPE,&tmp); No space between x,y, IIRC checkpatch reports that. >> + if (ret< 0) >> + goto err; >> + pr_debug("%s: ir_type=%02x\n", __func__, tmp); >> + >> + switch (tmp) { >> + case 0: /* NEC */ >> + default: >> + af9035_config.ir_rc6 = false; unused variable >> + d->props.rc.core.protocol = RC_TYPE_NEC; >> + d->props.rc.core.rc_codes = >> + RC_MAP_NEC_TERRATEC_CINERGY_XS; >> + break; >> + case 1: /* RC6 */ >> + af9035_config.ir_rc6 = true; >> + d->props.rc.core.protocol = RC_TYPE_RC6; >> + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; >> + break; >> + } I hate to default some random remote controller keytable. Use EMPTY map, it is for that. >> + } >> + >> return 0; >> >> err: >> @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties >> >> .i2c_algo =&af9035_i2c_algo, >> >> + .rc.core = { >> + .protocol = RC_TYPE_NEC, >> + .module_name = "af9035", >> + .rc_query = af9035_rc_query, >> + .rc_interval = AF9035_POLL, >> + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, Does this mean we promise userspace we can do both NEC and RC6? Does it mean we should offer method to change protocol in that case? I suspect it is not even possible to switch from remote protocol to other unless eeprom change or firmware hack. >> + .rc_codes = RC_MAP_EMPTY, /* may be changed in >> + af9035_read_mac_address */ Commented that earlier. But RC_MAP_EMPTY is correct choice for default. > > This is just a minor thing, but the comment here seems to be outdated, > as this is actually set at af9035_init(). > >> + }, >> .num_device_descs = 5, >> .devices = { >> { >> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h b/drivers/media/dvb/dvb-usb/af9035.h >> --- a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 +0200 >> +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 17:35:08.517840044 +0200 >> @@ -49,6 +49,8 @@ struct usb_req { >> >> struct config { >> bool dual_mode; >> + bool raw_ir; >> + bool ir_rc6; Both of these new configs are unused and not needed. Please do not add new configuration option unless needed (to pass config data from function to other inside driver). >> bool hw_not_supported; >> }; >> >> @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { >> #define CMD_MEM_WR 0x01 >> #define CMD_I2C_RD 0x02 >> #define CMD_I2C_WR 0x03 >> +#define CMD_IR_GET 0x18 >> #define CMD_FW_DL 0x21 >> #define CMD_FW_QUERYINFO 0x22 >> #define CMD_FW_BOOT 0x23 >> >> Hans-Frieder Vogt e-mail: hfvogt<at> gmx .dot. net > > Except for that minor mistake at the comment above, the rest looks fine on my eyes. I added some comments. And there was some basic remote controller issues - I didn't checked those, but those were commented as what is my understanding and some may be even wrong. In all cases please fix properly or explain I was wrong. regards Antti
Em 18-04-2012 11:57, Antti Palosaari escreveu: > I haven't tried to and not commented it. But I see clearly few problems. > > On 18.04.2012 17:17, Mauro Carvalho Chehab wrote: >> Em 07-04-2012 14:24, Hans-Frieder Vogt escreveu: >>> af9035: support remote controls. Currently, for remotes using the NEC protocol, >>> the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 the map of >>> RC_MAP_RC6_MCE. >>> >>> Signed-off-by: Hans-Frieder Vogt<hfvogt@gmx.net> >>> >>> drivers/media/dvb/dvb-usb/af9035.c | 72 +++++++++++++++++++++++++++++++++++++ >>> drivers/media/dvb/dvb-usb/af9035.h | 3 + >>> 2 files changed, 75 insertions(+) >>> >>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c b/drivers/media/dvb/dvb-usb/af9035.c >>> --- a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 +0200 >>> +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 19:17:55.044874329 +0200 >>> @@ -313,6 +313,41 @@ static struct i2c_algorithm af9035_i2c_a >>> .functionality = af9035_i2c_functionality, >>> }; >>> >>> +#define AF9035_POLL 250 >>> +static int af9035_rc_query(struct dvb_usb_device *d) >>> +{ >>> + unsigned int key; >>> + unsigned char b[4]; >>> + int ret; >>> + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; >>> + >>> + if (!af9035_config.raw_ir) >>> + return 0; >>> + >>> + ret = af9035_ctrl_msg(d->udev,&req); >>> + if (ret< 0) >>> + goto err; >>> + >>> + if ((b[2] + b[3]) == 0xff) { >>> + if ((b[0] + b[1]) == 0xff) { >>> + /* NEC */ >>> + key = b[0]<< 8 | b[2]; >>> + } else { >>> + /* ext. NEC */ >>> + key = b[0]<< 16 | b[1]<< 8 | b[2]; >>> + } >>> + } else { >>> + key = b[0]<< 24 | b[1]<< 16 | b[2]<< 8 | b[3]; >>> + } >>> + >>> + if (d->rc_dev != NULL) >>> + rc_keydown(d->rc_dev, key, 0); > > Is that checking needed and why? If there is no rc_device why we even call poll for it? Better to fix some core routines if that is true. > > Also rc_keydown() takes 2nd param as int, but in that case it does not matter. Anyhow, 3rd param is toggle which is used by RC5/6. IIRC I have never implemented RC5 or RC6 remote receiver, so I am not sure if it is needed and in which case. It is better to implement the toggle, when it is available/known, as the core will use it to detect when the same key was pressed quickly twice, or if someone just kept it pressed by a long time. When this is not implemented and someone presses the same key quickly twice (a "double click"), the second click will be ignored, if the time is lower than REP_DELAY (by default, 500 ms). Not all protocols/decoders can detect it though. NEC protocol can't. RC-5/RC-6 can do it. Yet, not all hardware reports the toggle big on RC-5. > >>> + >>> +err: >>> + /* ignore errors */ >>> + return 0; >>> +} >>> + >>> static int af9035_init(struct dvb_usb_device *d) >>> { >>> int ret, i; >>> @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc >>> for (i = 0; i< af9035_properties[0].num_adapters; i++) >>> af9035_af9033_config[i].clock = clock_lut[tmp]; >>> >>> + ret = af9035_rd_reg(d, EEPROM_IR_MODE,&tmp); >>> + if (ret< 0) >>> + goto err; >>> + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); >>> + af9035_config.raw_ir = tmp == 5; > > This looks odd for my eyes. Maybe x = (y == z); is better. Checkpatch didn't complain it? I think checkpatch will accept that. I generally prefer to use: foo = (tmp == 5) = true : false; as some source code analyzers complain about statements like the above. > >>> + >>> + if (af9035_config.raw_ir) { >>> + ret = af9035_rd_reg(d, EEPROM_IR_TYPE,&tmp); > > No space between x,y, IIRC checkpatch reports that. > >>> + if (ret< 0) >>> + goto err; >>> + pr_debug("%s: ir_type=%02x\n", __func__, tmp); >>> + >>> + switch (tmp) { >>> + case 0: /* NEC */ >>> + default: >>> + af9035_config.ir_rc6 = false; > > unused variable > >>> + d->props.rc.core.protocol = RC_TYPE_NEC; >>> + d->props.rc.core.rc_codes = >>> + RC_MAP_NEC_TERRATEC_CINERGY_XS; >>> + break; >>> + case 1: /* RC6 */ >>> + af9035_config.ir_rc6 = true; >>> + d->props.rc.core.protocol = RC_TYPE_RC6; >>> + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; >>> + break; >>> + } > > I hate to default some random remote controller keytable. Use EMPTY map, it is for that. > >>> + } >>> + >>> return 0; >>> >>> err: >>> @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties >>> >>> .i2c_algo =&af9035_i2c_algo, >>> >>> + .rc.core = { >>> + .protocol = RC_TYPE_NEC, >>> + .module_name = "af9035", >>> + .rc_query = af9035_rc_query, >>> + .rc_interval = AF9035_POLL, >>> + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, > > Does this mean we promise userspace we can do both NEC and RC6? Does it mean we should offer method to change protocol in that case? > I suspect it is not even possible to switch from remote protocol to other unless eeprom change or firmware hack. Yes, that assumes a callback to allow to switch the protocol, OR that the device can automatically recognize both protocols (there are a few that are able to handle both NEC and RC-5 or RC-6 without any specific command). The RC and NEC timings are very different, so, auto-detecting it is quite easy. If this is the case for af9035, all that it is needed test the protocol auto-detection is to replace the table from one protocol to the other and use an IR compatible with the new table. In the way this code was written, it leaves the reviewer without any af9035 device to believe that auto-detection is supported by af9035 (and also because there's no command sent to the device in order to switch the mode). It is easy to check if the device accepts both automatically: just load a different table with ir-keycode and test the remote with a different protocol. If this is not the case, then rc.core.allowed_protocols should be equal to rc.core.protocol. > >>> + .rc_codes = RC_MAP_EMPTY, /* may be changed in >>> + af9035_read_mac_address */ > > Commented that earlier. But RC_MAP_EMPTY is correct choice for default. > >> >> This is just a minor thing, but the comment here seems to be outdated, >> as this is actually set at af9035_init(). >> >>> + }, >>> .num_device_descs = 5, >>> .devices = { >>> { >>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h b/drivers/media/dvb/dvb-usb/af9035.h >>> --- a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 +0200 >>> +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 17:35:08.517840044 +0200 >>> @@ -49,6 +49,8 @@ struct usb_req { >>> >>> struct config { >>> bool dual_mode; >>> + bool raw_ir; >>> + bool ir_rc6; > > Both of these new configs are unused and not needed. Please do not add new configuration option unless needed (to pass config data from function to other inside driver). > >>> bool hw_not_supported; >>> }; >>> >>> @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { >>> #define CMD_MEM_WR 0x01 >>> #define CMD_I2C_RD 0x02 >>> #define CMD_I2C_WR 0x03 >>> +#define CMD_IR_GET 0x18 >>> #define CMD_FW_DL 0x21 >>> #define CMD_FW_QUERYINFO 0x22 >>> #define CMD_FW_BOOT 0x23 >>> >>> Hans-Frieder Vogt e-mail: hfvogt<at> gmx .dot. net >> >> Except for that minor mistake at the comment above, the rest looks fine on my eyes. > > I added some comments. And there was some basic remote controller issues - I didn't checked those, but those were commented as what is my understanding and some may be even wrong. In all cases please fix properly or explain I was wrong. > > regards > Antti -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Am Mittwoch, 18. April 2012 schrieb Mauro Carvalho Chehab: > Em 18-04-2012 11:57, Antti Palosaari escreveu: > > I haven't tried to and not commented it. But I see clearly few problems. > > > > On 18.04.2012 17:17, Mauro Carvalho Chehab wrote: > >> Em 07-04-2012 14:24, Hans-Frieder Vogt escreveu: > >>> af9035: support remote controls. Currently, for remotes using the NEC > >>> protocol, the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 > >>> the map of RC_MAP_RC6_MCE. > >>> > >>> Signed-off-by: Hans-Frieder Vogt<hfvogt@gmx.net> > >>> > >>> drivers/media/dvb/dvb-usb/af9035.c | 72 > >>> +++++++++++++++++++++++++++++++++++++ > >>> drivers/media/dvb/dvb-usb/af9035.h | 3 + > >>> 2 files changed, 75 insertions(+) > >>> > >>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c > >>> b/drivers/media/dvb/dvb-usb/af9035.c --- > >>> a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 > >>> +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 > >>> 19:17:55.044874329 +0200 @@ -313,6 +313,41 @@ static struct > >>> i2c_algorithm af9035_i2c_a > >>> > >>> .functionality = af9035_i2c_functionality, > >>> > >>> }; > >>> > >>> +#define AF9035_POLL 250 > >>> +static int af9035_rc_query(struct dvb_usb_device *d) > >>> +{ > >>> + unsigned int key; > >>> + unsigned char b[4]; > >>> + int ret; > >>> + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; > >>> + > >>> + if (!af9035_config.raw_ir) > >>> + return 0; > >>> + > >>> + ret = af9035_ctrl_msg(d->udev,&req); > >>> + if (ret< 0) > >>> + goto err; > >>> + > >>> + if ((b[2] + b[3]) == 0xff) { > >>> + if ((b[0] + b[1]) == 0xff) { > >>> + /* NEC */ > >>> + key = b[0]<< 8 | b[2]; > >>> + } else { > >>> + /* ext. NEC */ > >>> + key = b[0]<< 16 | b[1]<< 8 | b[2]; > >>> + } > >>> + } else { > >>> + key = b[0]<< 24 | b[1]<< 16 | b[2]<< 8 | b[3]; > >>> + } > >>> + > >>> + if (d->rc_dev != NULL) > >>> + rc_keydown(d->rc_dev, key, 0); > > > > Is that checking needed and why? If there is no rc_device why we even > > call poll for it? Better to fix some core routines if that is true. > > > > Also rc_keydown() takes 2nd param as int, but in that case it does not > > matter. Anyhow, 3rd param is toggle which is used by RC5/6. IIRC I have > > never implemented RC5 or RC6 remote receiver, so I am not sure if it is > > needed and in which case. > > It is better to implement the toggle, when it is available/known, as the > core will use it to detect when the same key was pressed quickly twice, or > if someone just kept it pressed by a long time. > > When this is not implemented and someone presses the same key quickly twice > (a "double click"), the second click will be ignored, if the time is lower > than REP_DELAY (by default, 500 ms). The IR_GET command only delivers 4 bytes, which give no indication of a repeated key. > > Not all protocols/decoders can detect it though. NEC protocol can't. > RC-5/RC-6 can do it. Yet, not all hardware reports the toggle big on RC-5. > > >>> + > >>> +err: > >>> + /* ignore errors */ > >>> + return 0; > >>> +} > >>> + > >>> > >>> static int af9035_init(struct dvb_usb_device *d) > >>> { > >>> > >>> int ret, i; > >>> > >>> @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc > >>> > >>> for (i = 0; i< af9035_properties[0].num_adapters; i++) > >>> > >>> af9035_af9033_config[i].clock = clock_lut[tmp]; > >>> > >>> + ret = af9035_rd_reg(d, EEPROM_IR_MODE,&tmp); > >>> + if (ret< 0) > >>> + goto err; > >>> + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); > >>> + af9035_config.raw_ir = tmp == 5; > > > > This looks odd for my eyes. Maybe x = (y == z); is better. Checkpatch > > didn't complain it? > > I think checkpatch will accept that. I generally prefer to use: > > foo = (tmp == 5) = true : false; shouldn't it rather be foo = (tmp == 5) ? true : false; > > as some source code analyzers complain about statements like the above. > > >>> + > >>> + if (af9035_config.raw_ir) { > >>> + ret = af9035_rd_reg(d, EEPROM_IR_TYPE,&tmp); > > > > No space between x,y, IIRC checkpatch reports that. the only errors that checkpatch is reporting is ERROR: trailing whitespace, but that seems to be normal for lines in the patch that are unchanged (I run checkpatch.pl --no-tree --file ...patch). > > > >>> + if (ret< 0) > >>> + goto err; > >>> + pr_debug("%s: ir_type=%02x\n", __func__, tmp); > >>> + > >>> + switch (tmp) { > >>> + case 0: /* NEC */ > >>> + default: > >>> + af9035_config.ir_rc6 = false; > > > > unused variable agreed. > > > >>> + d->props.rc.core.protocol = RC_TYPE_NEC; > >>> + d->props.rc.core.rc_codes = > >>> + RC_MAP_NEC_TERRATEC_CINERGY_XS; > >>> + break; > >>> + case 1: /* RC6 */ > >>> + af9035_config.ir_rc6 = true; > >>> + d->props.rc.core.protocol = RC_TYPE_RC6; > >>> + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; > >>> + break; > >>> + } > > > > I hate to default some random remote controller keytable. Use EMPTY map, > > it is for that. > > Good idea. > >>> + } > >>> + > >>> > >>> return 0; > >>> > >>> err: > >>> @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties > >>> > >>> .i2c_algo =&af9035_i2c_algo, > >>> > >>> + .rc.core = { > >>> + .protocol = RC_TYPE_NEC, > >>> + .module_name = "af9035", > >>> + .rc_query = af9035_rc_query, > >>> + .rc_interval = AF9035_POLL, > >>> + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, > > > > Does this mean we promise userspace we can do both NEC and RC6? Does it > > mean we should offer method to change protocol in that case? I suspect > > it is not even possible to switch from remote protocol to other unless > > eeprom change or firmware hack. > > Yes, that assumes a callback to allow to switch the protocol, OR that the > device can automatically recognize both protocols (there are a few that > are able to handle both NEC and RC-5 or RC-6 without any specific command). > The RC and NEC timings are very different, so, auto-detecting it is quite > easy. > > If this is the case for af9035, all that it is needed test the protocol > auto-detection is to replace the table from one protocol to the other and > use an IR compatible with the new table. I think the af9035 doesn't autodetect the protocol. I tested a device which is configured for RC6 (as layed down in the eeprom) and it doesn't read any raw code from a NEC rc. > In the way this code was written, it leaves the reviewer without any af9035 > device to believe that auto-detection is supported by af9035 (and also > because there's no command sent to the device in order to switch the mode). > > It is easy to check if the device accepts both automatically: just load > a different table with ir-keycode and test the remote with a different > protocol. > > If this is not the case, then rc.core.allowed_protocols should be equal to > rc.core.protocol. Thanks. > > >>> + .rc_codes = RC_MAP_EMPTY, /* may be changed in > >>> + af9035_read_mac_address */ > > > > Commented that earlier. But RC_MAP_EMPTY is correct choice for default. > > > >> This is just a minor thing, but the comment here seems to be outdated, > >> as this is actually set at af9035_init(). > >> > >>> + }, > >>> > >>> .num_device_descs = 5, > >>> .devices = { > >>> > >>> { > >>> > >>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h > >>> b/drivers/media/dvb/dvb-usb/af9035.h --- > >>> a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 > >>> +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 > >>> 17:35:08.517840044 +0200 @@ -49,6 +49,8 @@ struct usb_req { > >>> > >>> struct config { > >>> > >>> bool dual_mode; > >>> > >>> + bool raw_ir; > >>> + bool ir_rc6; > > > > Both of these new configs are unused and not needed. Please do not add > > new configuration option unless needed (to pass config data from > > function to other inside driver). raw_ir is indeed used (see af9035_rc_query). However I agree that I could implement this switch in a different way without the need of an extra config variable. > > > >>> bool hw_not_supported; > >>> > >>> }; > >>> > >>> @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { > >>> > >>> #define CMD_MEM_WR 0x01 > >>> #define CMD_I2C_RD 0x02 > >>> #define CMD_I2C_WR 0x03 > >>> > >>> +#define CMD_IR_GET 0x18 > >>> > >>> #define CMD_FW_DL 0x21 > >>> #define CMD_FW_QUERYINFO 0x22 > >>> #define CMD_FW_BOOT 0x23 > >>> > >>> Hans-Frieder Vogt e-mail: hfvogt<at> gmx .dot. > >>> net > >> > >> Except for that minor mistake at the comment above, the rest looks fine > >> on my eyes. > > > > I added some comments. And there was some basic remote controller issues > > - I didn't checked those, but those were commented as what is my > > understanding and some may be even wrong. In all cases please fix > > properly or explain I was wrong. > > > > regards > > Antti Thanks, Mauro and Antti, for your comments. Expect an improved patch soon. Cheers, Hans-Frieder Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Em 18-04-2012 17:42, Hans-Frieder Vogt escreveu: > Am Mittwoch, 18. April 2012 schrieb Mauro Carvalho Chehab: >> Em 18-04-2012 11:57, Antti Palosaari escreveu: >>> I haven't tried to and not commented it. But I see clearly few problems. >>> >>> On 18.04.2012 17:17, Mauro Carvalho Chehab wrote: >>>> Em 07-04-2012 14:24, Hans-Frieder Vogt escreveu: >>>>> af9035: support remote controls. Currently, for remotes using the NEC >>>>> protocol, the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 >>>>> the map of RC_MAP_RC6_MCE. >>>>> >>>>> Signed-off-by: Hans-Frieder Vogt<hfvogt@gmx.net> >>>>> >>>>> drivers/media/dvb/dvb-usb/af9035.c | 72 >>>>> +++++++++++++++++++++++++++++++++++++ >>>>> drivers/media/dvb/dvb-usb/af9035.h | 3 + >>>>> 2 files changed, 75 insertions(+) >>>>> >>>>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c >>>>> b/drivers/media/dvb/dvb-usb/af9035.c --- >>>>> a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 >>>>> +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 >>>>> 19:17:55.044874329 +0200 @@ -313,6 +313,41 @@ static struct >>>>> i2c_algorithm af9035_i2c_a >>>>> >>>>> .functionality = af9035_i2c_functionality, >>>>> >>>>> }; >>>>> >>>>> +#define AF9035_POLL 250 >>>>> +static int af9035_rc_query(struct dvb_usb_device *d) >>>>> +{ >>>>> + unsigned int key; >>>>> + unsigned char b[4]; >>>>> + int ret; >>>>> + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; >>>>> + >>>>> + if (!af9035_config.raw_ir) >>>>> + return 0; >>>>> + >>>>> + ret = af9035_ctrl_msg(d->udev,&req); >>>>> + if (ret< 0) >>>>> + goto err; >>>>> + >>>>> + if ((b[2] + b[3]) == 0xff) { >>>>> + if ((b[0] + b[1]) == 0xff) { >>>>> + /* NEC */ >>>>> + key = b[0]<< 8 | b[2]; >>>>> + } else { >>>>> + /* ext. NEC */ >>>>> + key = b[0]<< 16 | b[1]<< 8 | b[2]; >>>>> + } >>>>> + } else { >>>>> + key = b[0]<< 24 | b[1]<< 16 | b[2]<< 8 | b[3]; >>>>> + } >>>>> + >>>>> + if (d->rc_dev != NULL) >>>>> + rc_keydown(d->rc_dev, key, 0); >>> >>> Is that checking needed and why? If there is no rc_device why we even >>> call poll for it? Better to fix some core routines if that is true. >>> >>> Also rc_keydown() takes 2nd param as int, but in that case it does not >>> matter. Anyhow, 3rd param is toggle which is used by RC5/6. IIRC I have >>> never implemented RC5 or RC6 remote receiver, so I am not sure if it is >>> needed and in which case. >> >> It is better to implement the toggle, when it is available/known, as the >> core will use it to detect when the same key was pressed quickly twice, or >> if someone just kept it pressed by a long time. >> >> When this is not implemented and someone presses the same key quickly twice >> (a "double click"), the second click will be ignored, if the time is lower >> than REP_DELAY (by default, 500 ms). > > The IR_GET command only delivers 4 bytes, which give no indication of a > repeated key. > >> >> Not all protocols/decoders can detect it though. NEC protocol can't. >> RC-5/RC-6 can do it. Yet, not all hardware reports the toggle big on RC-5. >> >>>>> + >>>>> +err: >>>>> + /* ignore errors */ >>>>> + return 0; >>>>> +} >>>>> + >>>>> >>>>> static int af9035_init(struct dvb_usb_device *d) >>>>> { >>>>> >>>>> int ret, i; >>>>> >>>>> @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc >>>>> >>>>> for (i = 0; i< af9035_properties[0].num_adapters; i++) >>>>> >>>>> af9035_af9033_config[i].clock = clock_lut[tmp]; >>>>> >>>>> + ret = af9035_rd_reg(d, EEPROM_IR_MODE,&tmp); >>>>> + if (ret< 0) >>>>> + goto err; >>>>> + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); >>>>> + af9035_config.raw_ir = tmp == 5; >>> >>> This looks odd for my eyes. Maybe x = (y == z); is better. Checkpatch >>> didn't complain it? >> >> I think checkpatch will accept that. I generally prefer to use: >> >> foo = (tmp == 5) = true : false; > > shouldn't it rather be > foo = (tmp == 5) ? true : false; Yes. >> >> as some source code analyzers complain about statements like the above. >> >>>>> + >>>>> + if (af9035_config.raw_ir) { >>>>> + ret = af9035_rd_reg(d, EEPROM_IR_TYPE,&tmp); >>> >>> No space between x,y, IIRC checkpatch reports that. > > the only errors that checkpatch is reporting is ERROR: trailing whitespace, > but that seems to be normal for lines in the patch that are unchanged (I run > checkpatch.pl --no-tree --file ...patch). Use checkpatch for your patch, not for the file. Unfortunately, when there are function parameters are all upercase, checkpatch.pl doesn't work well. Once I complained, it was said this is a feature, in order to avoid some false-positives. > >>> >>>>> + if (ret< 0) >>>>> + goto err; >>>>> + pr_debug("%s: ir_type=%02x\n", __func__, tmp); >>>>> + >>>>> + switch (tmp) { >>>>> + case 0: /* NEC */ >>>>> + default: >>>>> + af9035_config.ir_rc6 = false; >>> >>> unused variable > > agreed. > >>> >>>>> + d->props.rc.core.protocol = RC_TYPE_NEC; >>>>> + d->props.rc.core.rc_codes = >>>>> + RC_MAP_NEC_TERRATEC_CINERGY_XS; >>>>> + break; >>>>> + case 1: /* RC6 */ >>>>> + af9035_config.ir_rc6 = true; >>>>> + d->props.rc.core.protocol = RC_TYPE_RC6; >>>>> + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; >>>>> + break; >>>>> + } >>> >>> I hate to default some random remote controller keytable. Use EMPTY map, >>> it is for that. >>> > Good idea. > >>>>> + } >>>>> + >>>>> >>>>> return 0; >>>>> >>>>> err: >>>>> @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties >>>>> >>>>> .i2c_algo =&af9035_i2c_algo, >>>>> >>>>> + .rc.core = { >>>>> + .protocol = RC_TYPE_NEC, >>>>> + .module_name = "af9035", >>>>> + .rc_query = af9035_rc_query, >>>>> + .rc_interval = AF9035_POLL, >>>>> + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, >>> >>> Does this mean we promise userspace we can do both NEC and RC6? Does it >>> mean we should offer method to change protocol in that case? I suspect >>> it is not even possible to switch from remote protocol to other unless >>> eeprom change or firmware hack. >> >> Yes, that assumes a callback to allow to switch the protocol, OR that the >> device can automatically recognize both protocols (there are a few that >> are able to handle both NEC and RC-5 or RC-6 without any specific command). >> The RC and NEC timings are very different, so, auto-detecting it is quite >> easy. >> >> If this is the case for af9035, all that it is needed test the protocol >> auto-detection is to replace the table from one protocol to the other and >> use an IR compatible with the new table. > > I think the af9035 doesn't autodetect the protocol. I tested a device which is > configured for RC6 (as layed down in the eeprom) and it doesn't read any raw > code from a NEC rc. Then, you need to make allowed_protocols equal to protocol, for the userspace tools to work properly with it. >> In the way this code was written, it leaves the reviewer without any af9035 >> device to believe that auto-detection is supported by af9035 (and also >> because there's no command sent to the device in order to switch the mode). >> >> It is easy to check if the device accepts both automatically: just load >> a different table with ir-keycode and test the remote with a different >> protocol. >> >> If this is not the case, then rc.core.allowed_protocols should be equal to >> rc.core.protocol. > > Thanks. > >> >>>>> + .rc_codes = RC_MAP_EMPTY, /* may be changed in >>>>> + af9035_read_mac_address */ >>> >>> Commented that earlier. But RC_MAP_EMPTY is correct choice for default. >>> >>>> This is just a minor thing, but the comment here seems to be outdated, >>>> as this is actually set at af9035_init(). >>>> >>>>> + }, >>>>> >>>>> .num_device_descs = 5, >>>>> .devices = { >>>>> >>>>> { >>>>> >>>>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h >>>>> b/drivers/media/dvb/dvb-usb/af9035.h --- >>>>> a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 >>>>> +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 >>>>> 17:35:08.517840044 +0200 @@ -49,6 +49,8 @@ struct usb_req { >>>>> >>>>> struct config { >>>>> >>>>> bool dual_mode; >>>>> >>>>> + bool raw_ir; >>>>> + bool ir_rc6; >>> >>> Both of these new configs are unused and not needed. Please do not add >>> new configuration option unless needed (to pass config data from >>> function to other inside driver). > > raw_ir is indeed used (see af9035_rc_query). However I agree that I could > implement this switch in a different way without the need of an extra config > variable. If you choose to keep it, please don't call it as "raw_ir". Raw IR's are the ones that sends a sequence of pulse-space events to the Kernel, for them to be handled by a software decoder. What you're adding is, instead, a hardware decoded IR device. > >>> >>>>> bool hw_not_supported; >>>>> >>>>> }; >>>>> >>>>> @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { >>>>> >>>>> #define CMD_MEM_WR 0x01 >>>>> #define CMD_I2C_RD 0x02 >>>>> #define CMD_I2C_WR 0x03 >>>>> >>>>> +#define CMD_IR_GET 0x18 >>>>> >>>>> #define CMD_FW_DL 0x21 >>>>> #define CMD_FW_QUERYINFO 0x22 >>>>> #define CMD_FW_BOOT 0x23 >>>>> >>>>> Hans-Frieder Vogt e-mail: hfvogt<at> gmx .dot. >>>>> net >>>> >>>> Except for that minor mistake at the comment above, the rest looks fine >>>> on my eyes. >>> >>> I added some comments. And there was some basic remote controller issues >>> - I didn't checked those, but those were commented as what is my >>> understanding and some may be even wrong. In all cases please fix >>> properly or explain I was wrong. >>> >>> regards >>> Antti > > Thanks, Mauro and Antti, for your comments. Expect an improved patch soon. > > Cheers, > Hans-Frieder > > Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 18.04.2012 23:42, Hans-Frieder Vogt wrote: > Am Mittwoch, 18. April 2012 schrieb Mauro Carvalho Chehab: >> Em 18-04-2012 11:57, Antti Palosaari escreveu: >>> I haven't tried to and not commented it. But I see clearly few problems. >>> >>> On 18.04.2012 17:17, Mauro Carvalho Chehab wrote: >>>> Em 07-04-2012 14:24, Hans-Frieder Vogt escreveu: >>>>> af9035: support remote controls. Currently, for remotes using the NEC >>>>> protocol, the map of the TERRATEC_CINERGY_XS remote is loaded, for RC6 >>>>> the map of RC_MAP_RC6_MCE. >>>>> >>>>> Signed-off-by: Hans-Frieder Vogt<hfvogt@gmx.net> >>>>> >>>>> drivers/media/dvb/dvb-usb/af9035.c | 72 >>>>> +++++++++++++++++++++++++++++++++++++ >>>>> drivers/media/dvb/dvb-usb/af9035.h | 3 + >>>>> 2 files changed, 75 insertions(+) >>>>> >>>>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c >>>>> b/drivers/media/dvb/dvb-usb/af9035.c --- >>>>> a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 >>>>> +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 >>>>> 19:17:55.044874329 +0200 @@ -313,6 +313,41 @@ static struct >>>>> i2c_algorithm af9035_i2c_a >>>>> >>>>> .functionality = af9035_i2c_functionality, >>>>> >>>>> }; >>>>> >>>>> +#define AF9035_POLL 250 >>>>> +static int af9035_rc_query(struct dvb_usb_device *d) >>>>> +{ >>>>> + unsigned int key; >>>>> + unsigned char b[4]; >>>>> + int ret; >>>>> + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; >>>>> + >>>>> + if (!af9035_config.raw_ir) >>>>> + return 0; >>>>> + >>>>> + ret = af9035_ctrl_msg(d->udev,&req); >>>>> + if (ret< 0) >>>>> + goto err; >>>>> + >>>>> + if ((b[2] + b[3]) == 0xff) { >>>>> + if ((b[0] + b[1]) == 0xff) { >>>>> + /* NEC */ >>>>> + key = b[0]<< 8 | b[2]; >>>>> + } else { >>>>> + /* ext. NEC */ >>>>> + key = b[0]<< 16 | b[1]<< 8 | b[2]; >>>>> + } >>>>> + } else { >>>>> + key = b[0]<< 24 | b[1]<< 16 | b[2]<< 8 | b[3]; >>>>> + } >>>>> + >>>>> + if (d->rc_dev != NULL) >>>>> + rc_keydown(d->rc_dev, key, 0); >>> >>> Is that checking needed and why? If there is no rc_device why we even >>> call poll for it? Better to fix some core routines if that is true. >>> >>> Also rc_keydown() takes 2nd param as int, but in that case it does not >>> matter. Anyhow, 3rd param is toggle which is used by RC5/6. IIRC I have >>> never implemented RC5 or RC6 remote receiver, so I am not sure if it is >>> needed and in which case. >> >> It is better to implement the toggle, when it is available/known, as the >> core will use it to detect when the same key was pressed quickly twice, or >> if someone just kept it pressed by a long time. >> >> When this is not implemented and someone presses the same key quickly twice >> (a "double click"), the second click will be ignored, if the time is lower >> than REP_DELAY (by default, 500 ms). > > The IR_GET command only delivers 4 bytes, which give no indication of a > repeated key. Then it is good idea to add comment why it is not used, as normally RC5/RC6 uses it. As a side note, I implemented AF9015 remote reading IR codes directly from the RAM and leaving firmware command unused. That was mainly due to HID problems (starts repeating wildly due to chip sets wrong USB polling interval) and also gain full control to remote. Similar solution could be nice for that driver too. >> Not all protocols/decoders can detect it though. NEC protocol can't. >> RC-5/RC-6 can do it. Yet, not all hardware reports the toggle big on RC-5. >> >>>>> + >>>>> +err: >>>>> + /* ignore errors */ >>>>> + return 0; >>>>> +} >>>>> + >>>>> >>>>> static int af9035_init(struct dvb_usb_device *d) >>>>> { >>>>> >>>>> int ret, i; >>>>> >>>>> @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc >>>>> >>>>> for (i = 0; i< af9035_properties[0].num_adapters; i++) >>>>> >>>>> af9035_af9033_config[i].clock = clock_lut[tmp]; >>>>> >>>>> + ret = af9035_rd_reg(d, EEPROM_IR_MODE,&tmp); >>>>> + if (ret< 0) >>>>> + goto err; >>>>> + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); >>>>> + af9035_config.raw_ir = tmp == 5; >>> >>> This looks odd for my eyes. Maybe x = (y == z); is better. Checkpatch >>> didn't complain it? >> >> I think checkpatch will accept that. I generally prefer to use: >> >> foo = (tmp == 5) = true : false; > > shouldn't it rather be > foo = (tmp == 5) ? true : false; >> >> as some source code analyzers complain about statements like the above. Maybe whole boolean conversion can be dropped. I suspect there is more possible values than than 5 and !5. >>>>> + >>>>> + if (af9035_config.raw_ir) { >>>>> + ret = af9035_rd_reg(d, EEPROM_IR_TYPE,&tmp); >>> >>> No space between x,y, IIRC checkpatch reports that. > > the only errors that checkpatch is reporting is ERROR: trailing whitespace, > but that seems to be normal for lines in the patch that are unchanged (I run > checkpatch.pl --no-tree --file ...patch). I still like idea to add one space after comma always > >>> >>>>> + if (ret< 0) >>>>> + goto err; >>>>> + pr_debug("%s: ir_type=%02x\n", __func__, tmp); >>>>> + >>>>> + switch (tmp) { >>>>> + case 0: /* NEC */ >>>>> + default: >>>>> + af9035_config.ir_rc6 = false; >>> >>> unused variable > > agreed. > >>> >>>>> + d->props.rc.core.protocol = RC_TYPE_NEC; >>>>> + d->props.rc.core.rc_codes = >>>>> + RC_MAP_NEC_TERRATEC_CINERGY_XS; >>>>> + break; >>>>> + case 1: /* RC6 */ >>>>> + af9035_config.ir_rc6 = true; >>>>> + d->props.rc.core.protocol = RC_TYPE_RC6; >>>>> + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; >>>>> + break; >>>>> + } >>> >>> I hate to default some random remote controller keytable. Use EMPTY map, >>> it is for that. >>> > Good idea. > >>>>> + } >>>>> + >>>>> >>>>> return 0; >>>>> >>>>> err: >>>>> @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties >>>>> >>>>> .i2c_algo =&af9035_i2c_algo, >>>>> >>>>> + .rc.core = { >>>>> + .protocol = RC_TYPE_NEC, >>>>> + .module_name = "af9035", >>>>> + .rc_query = af9035_rc_query, >>>>> + .rc_interval = AF9035_POLL, >>>>> + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, >>> >>> Does this mean we promise userspace we can do both NEC and RC6? Does it >>> mean we should offer method to change protocol in that case? I suspect >>> it is not even possible to switch from remote protocol to other unless >>> eeprom change or firmware hack. >> >> Yes, that assumes a callback to allow to switch the protocol, OR that the >> device can automatically recognize both protocols (there are a few that >> are able to handle both NEC and RC-5 or RC-6 without any specific command). >> The RC and NEC timings are very different, so, auto-detecting it is quite >> easy. >> >> If this is the case for af9035, all that it is needed test the protocol >> auto-detection is to replace the table from one protocol to the other and >> use an IR compatible with the new table. > > I think the af9035 doesn't autodetect the protocol. I tested a device which is > configured for RC6 (as layed down in the eeprom) and it doesn't read any raw > code from a NEC rc. > >> In the way this code was written, it leaves the reviewer without any af9035 >> device to believe that auto-detection is supported by af9035 (and also >> because there's no command sent to the device in order to switch the mode). >> >> It is easy to check if the device accepts both automatically: just load >> a different table with ir-keycode and test the remote with a different >> protocol. >> >> If this is not the case, then rc.core.allowed_protocols should be equal to >> rc.core.protocol. > > Thanks. > >> >>>>> + .rc_codes = RC_MAP_EMPTY, /* may be changed in >>>>> + af9035_read_mac_address */ >>> >>> Commented that earlier. But RC_MAP_EMPTY is correct choice for default. >>> >>>> This is just a minor thing, but the comment here seems to be outdated, >>>> as this is actually set at af9035_init(). >>>> >>>>> + }, >>>>> >>>>> .num_device_descs = 5, >>>>> .devices = { >>>>> >>>>> { >>>>> >>>>> diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h >>>>> b/drivers/media/dvb/dvb-usb/af9035.h --- >>>>> a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 >>>>> +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 >>>>> 17:35:08.517840044 +0200 @@ -49,6 +49,8 @@ struct usb_req { >>>>> >>>>> struct config { >>>>> >>>>> bool dual_mode; >>>>> >>>>> + bool raw_ir; >>>>> + bool ir_rc6; >>> >>> Both of these new configs are unused and not needed. Please do not add >>> new configuration option unless needed (to pass config data from >>> function to other inside driver). > > raw_ir is indeed used (see af9035_rc_query). However I agree that I could > implement this switch in a different way without the need of an extra config > variable. Hmmm, OK, I may be then wrong, it is a little bit hard to review patches using mailer. But of course it is wise to some configuration values if needed continuously. Very good reason is for example avoid I/O (register read / write) when polling remote. But for the remote, most info is already stored to device properties structure and existing info should used instead of duplicating same info to multiple locations. > >>> >>>>> bool hw_not_supported; >>>>> >>>>> }; >>>>> >>>>> @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { >>>>> >>>>> #define CMD_MEM_WR 0x01 >>>>> #define CMD_I2C_RD 0x02 >>>>> #define CMD_I2C_WR 0x03 >>>>> >>>>> +#define CMD_IR_GET 0x18 >>>>> >>>>> #define CMD_FW_DL 0x21 >>>>> #define CMD_FW_QUERYINFO 0x22 >>>>> #define CMD_FW_BOOT 0x23 >>>>> >>>>> Hans-Frieder Vogt e-mail: hfvogt<at> gmx .dot. >>>>> net >>>> >>>> Except for that minor mistake at the comment above, the rest looks fine >>>> on my eyes. >>> >>> I added some comments. And there was some basic remote controller issues >>> - I didn't checked those, but those were commented as what is my >>> understanding and some may be even wrong. In all cases please fix >>> properly or explain I was wrong. >>> >>> regards >>> Antti > > Thanks, Mauro and Antti, for your comments. Expect an improved patch soon. > > Cheers, > Hans-Frieder > > Hans-Frieder Vogt e-mail: hfvogt<at> gmx .dot. net regards Antti
Em 18-04-2012 18:12, Antti Palosaari escreveu: > On 18.04.2012 23:42, Hans-Frieder Vogt wrote: >> Am Mittwoch, 18. April 2012 schrieb Mauro Carvalho Chehab: >>> Em 18-04-2012 11:57, Antti Palosaari escreveu: >>>>>> + >>>>>> + if (af9035_config.raw_ir) { >>>>>> + ret = af9035_rd_reg(d, EEPROM_IR_TYPE,&tmp); >>>> >>>> No space between x,y, IIRC checkpatch reports that. >> >> the only errors that checkpatch is reporting is ERROR: trailing whitespace, >> but that seems to be normal for lines in the patch that are unchanged (I run >> checkpatch.pl --no-tree --file ...patch). > > I still like idea to add one space after comma always Me too. The above, even passing on checkpatch, is not the right CodingStyle. Regards, Mauro -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.c b/drivers/media/dvb/dvb-usb/af9035.c --- a/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 15:59:56.000000000 +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.c 2012-04-07 19:17:55.044874329 +0200 @@ -313,6 +313,41 @@ static struct i2c_algorithm af9035_i2c_a .functionality = af9035_i2c_functionality, }; +#define AF9035_POLL 250 +static int af9035_rc_query(struct dvb_usb_device *d) +{ + unsigned int key; + unsigned char b[4]; + int ret; + struct usb_req req = { CMD_IR_GET, 0, 0, NULL, 4, b }; + + if (!af9035_config.raw_ir) + return 0; + + ret = af9035_ctrl_msg(d->udev, &req); + if (ret < 0) + goto err; + + if ((b[2] + b[3]) == 0xff) { + if ((b[0] + b[1]) == 0xff) { + /* NEC */ + key = b[0] << 8 | b[2]; + } else { + /* ext. NEC */ + key = b[0] << 16 | b[1] << 8 | b[2]; + } + } else { + key = b[0] << 24 | b[1] << 16 | b[2] << 8 | b[3]; + } + + if (d->rc_dev != NULL) + rc_keydown(d->rc_dev, key, 0); + +err: + /* ignore errors */ + return 0; +} + static int af9035_init(struct dvb_usb_device *d) { int ret, i; @@ -627,6 +662,34 @@ static int af9035_read_mac_address(struc for (i = 0; i < af9035_properties[0].num_adapters; i++) af9035_af9033_config[i].clock = clock_lut[tmp]; + ret = af9035_rd_reg(d, EEPROM_IR_MODE, &tmp); + if (ret < 0) + goto err; + pr_debug("%s: ir_mode=%02x\n", __func__, tmp); + af9035_config.raw_ir = tmp == 5; + + if (af9035_config.raw_ir) { + ret = af9035_rd_reg(d, EEPROM_IR_TYPE, &tmp); + if (ret < 0) + goto err; + pr_debug("%s: ir_type=%02x\n", __func__, tmp); + + switch (tmp) { + case 0: /* NEC */ + default: + af9035_config.ir_rc6 = false; + d->props.rc.core.protocol = RC_TYPE_NEC; + d->props.rc.core.rc_codes = + RC_MAP_NEC_TERRATEC_CINERGY_XS; + break; + case 1: /* RC6 */ + af9035_config.ir_rc6 = true; + d->props.rc.core.protocol = RC_TYPE_RC6; + d->props.rc.core.rc_codes = RC_MAP_RC6_MCE; + break; + } + } + return 0; err: @@ -1003,6 +1066,15 @@ static struct dvb_usb_device_properties .i2c_algo = &af9035_i2c_algo, + .rc.core = { + .protocol = RC_TYPE_NEC, + .module_name = "af9035", + .rc_query = af9035_rc_query, + .rc_interval = AF9035_POLL, + .allowed_protos = RC_TYPE_NEC | RC_TYPE_RC6, + .rc_codes = RC_MAP_EMPTY, /* may be changed in + af9035_read_mac_address */ + }, .num_device_descs = 5, .devices = { { diff -Nupr a/drivers/media/dvb/dvb-usb/af9035.h b/drivers/media/dvb/dvb-usb/af9035.h --- a/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 15:58:43.000000000 +0200 +++ b/drivers/media/dvb/dvb-usb/af9035.h 2012-04-07 17:35:08.517840044 +0200 @@ -49,6 +49,8 @@ struct usb_req { struct config { bool dual_mode; + bool raw_ir; + bool ir_rc6; bool hw_not_supported; }; @@ -96,6 +98,7 @@ u32 clock_lut_it9135[] = { #define CMD_MEM_WR 0x01 #define CMD_I2C_RD 0x02 #define CMD_I2C_WR 0x03 +#define CMD_IR_GET 0x18 #define CMD_FW_DL 0x21 #define CMD_FW_QUERYINFO 0x22 #define CMD_FW_BOOT 0x23